Manual Constructa CD636253 (page 27 of 56) (English, German, Dutch, French)

714956

Zoom out

Zoom in

1/56

Finishing installation of the appliance

1. Drill an 8mm Øhole to a depth of 80mm for the safety screw

and press the wall plug flush into the wall. ¨

2. First remove the protective foil from the back of the appliance

and, following installation, remove the foil completely.

3. Connect the appliance. ©

4. Screw in the safety screw - and washer - and tighten all the

screws. ª

Exhaust duct

Note: The device manufacturer does not assume any warranty

for complaints attributable to the pipe section.

■ The device achieves its optimum performance by means of a

short, straight exhaust air pipe and as large a pipe diameter

as possible.

■ As a result of long rough exhaust air pipes, many pipe bends

or pipe diameters that are smaller than 150 mm, the optimum

extraction performance is not achieved and fan noise is

increased.

■ The pipes or hoses for laying the exhaust air line must

consist of non-combustible material.

Round pipes

An inner diameter of 150 mm, but at least 120 mm, is

recommended.

Flat ducts

The inner cross-section must correspond to the diameter of the

round pipes.

dia. 150 mm ca. 177 cm

dia. 120 mm ca. 113 cm

■ Flat ducts should not have any sharp deflections.

■ Use sealing strips for deviating pipe diameters.

Connecting the appliance to the power supply

Connecting the air extractor

Note: If using an aluminium pipe, smooth the connection area

beforehand.

1. Attach the air extractor pipe directly to the air-pipe connector.

2. Connect to air extractor opening.

3. Seal the joints appropriately.

Connect the power supply

1. Plug the mains plug into the earthed socket.

2. If a fixed connection is required, please follow the instructions

in the Electrical Connection section.

Attaching the flue duct

: Risk of injury!

Components inside the appliance may have sharp edges. Wear

protective gloves.

1. Separate the flue duct sections.

To do this, remove the adhesive tape.

2. Remove the pieces of protective film from both flue duct

sections.

3. Push one flue duct section into the other.

Notes

■ To prevent scratches, lay paper over the edges of the outer

flue duct section to protect the surface.

■ The slots of the inner flue duct section should point

downwards.

4. Place the flue ducts sections on the appliance.

5. Slide the inner flue duct section upwards, and attach it to the

left and right sides of the retaining bracket. ¨

7. Screw the flue duct section to the sides of the retaining

bracket using two screws. ª

8. Use two screws to fasten the outer flue duct section to the

appliance from below. «

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Constructa CD636253 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 3,2 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Constructa CD636253 Manual

Product: