652338
58
Zoom out
Zoom in
Previous page
1/80
Next page
58 Mounting and installation work
ACCESSORY BOARD
REMOTE BOARD
BMSLinkUpSAB
3V
CR2032
BAT
SD
J7
J4
J8
J11
(USB)
(RJ45)
GND + GND + GND + 24VGND
MAINS SUPPLY
L N SC1SC2PE PE
MODULE B
24VDC
LEVEL
UNIT
POWER
BOARD
DRN1 J2
INLET J1
PWR
SUPPLY
BLOWERLIMIT ENABLECONTROL
V+
X8
X9
X12
X11
X10
X7
X1
INGND IN GND 24V IN24V IN 24V GND
RS485 RS485PWRIC
CONT-
ACTOR
HEAT GR.
2+3
JP2 (24V)
JP1 (10V)
PUMP
AC
SWITCH
GND D–D+ GND D–D+24V GND
DRN2 J3
F1
SW1
F2
H1
Error
1 2 3
Service
4 5 6
Steam
7 8
Unit On
9 10
H2
Hyg. Valve A FAN B
1 2 3
Hyg. Valve B
4 5 6
7 8
FAN A
9 10
L1 L2 L3
L1 L2 L3 PE
K1
THV
Q3
F3
Y1
200-600 V/3~/50..60 Hz
230 V/1~/50..60 Hz
L1 N PE
Q3
F3
B3
B2
B1
L1 N PE
F4
Q4
230 V/1~/50..60 Hz
K2
J3
J1
230V
M
L1 N PE
140Ω...10kΩ
A2
On/Off
A3
GND
IN
V+
IN
V+
JP1
JP2
A1
A4
Y
+
Z
+
B4
140Ω...10kΩ
A5
GND
IN
V+
JP1
Z
L1 L2 L3
400-500 V/3~/50..60 Hz
400-415 V/3~N/50..60 Hz
F3
Q3
L2 L3L1
L2 L3 PEL1
L1 N PE
F3
Q3
L2 L3 PENL1
L2 L3L1
N PEL1
Control compartment
Driver board
Option TR (3Ph)
Option CVI (3Ph+N)
5.7.2 Wiring diagram Condair RS 5...40 - Single units "S" and "M"
Fig. 27: Wiring diagram Condair RS - Single units "S" and "M" (5...40 kg/h)
A1 Continuous humidity controller (active) or humidity sensor
A2 Ohmic humidity controller (passive),
set jumper JP1 and remove jumper JP2
A3 On/Off humidity controller,
set jumper JP2 and remove jumper JP1
A4 Limiter signal
A2 Ohmic limiter controller, set jumper JP1 and remove jumper JP2
B1 Ventilation interlock
B2 Airow monitor
B3 Safety humidistat
B4 External enable contact
F1 Internal fuse 24V supply (1 A, slow acting)
F2 Internal fuse 230V supply (6.3 A, slow acting)
F3 External fuse heating voltage supply
(see table in chapter 5.7.7)
F4 External fuse control voltage (max. 10 A, slow acting)
J1 Jumper wire, if blower pack safety loop is not connected
J3 Jumper wire, if no monitoring devices are connected to SC1 and SC2
J4 Jumper for activating the terminating resistor for Modbus network
(Jumper must be connected, if Condair RS is the last unit in the
Modbus network)
J7 Jumper for activating Modbus or BACnet MSTP communication via
RS485 interface (J6). If jumper is not in place no communication will
take place through the RS485 interface.
H1 Remote operating and fault indication (option)
H2 Accessory board (option) for the control of an external fan of the AHU
as well as the optional external valve for the water supply line ushing
K1 Mains contactor (heating voltage)
K2 External safety circuit (safety humidistat, airow monitor, etc.)
M Motor blower pack
Q3 External main switch heating voltage supply
Q4 External main switch control voltage supply
SW1 Rotary switch Module identication (must be left on position "0")
THV Terminal Heating voltage supply (option)
Y1 Total drain valve (option)
6.3 A, slow acting
6.3 A, slow acting
Ethernet (RJ45)
IP network / BMS BACnet IP
RS 485
BACnet MSTP
Control board
58


Need help? Post your question in this forum.

Forumrules
1

Forum

condair-rs

Reset search

  • why drain hose led to left, is it due to electrical on right side.
    Submitted on 29-8-2022 at 23:32

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Condair RS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Condair RS in the language / languages: English as an attachment in your email.

The manual is 7,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Condair RS

Condair RS User Manual - English - 80 pages

Condair RS User Manual - Dutch - 80 pages

Condair RS Installation Guide - Dutch - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info