652338
44
Zoom out
Zoom in
Previous page
1/80
Next page
44 Mounting and installation work
5.4.5 Installing the steam and condensate lines
Installations notes
Use original steam and condensate hose from your Condair representative or solid steam pipes
from copper or stainless steel (min. DIN 1.4301) exclusively. Steam and condensate lines from
other material may cause undesired operational malfunctions.
Initially, lead the steam line upright upwards min. 300 mm above the humidier. Then lead the
steam line with a minimum upslope and/or a minimum downslope of 15 %/8.5° to the steam
distributor.
The condensate hose from the steam distributor is led down to the humidier with a minimum
downslope of 15 %/8.5°, via a condensate trap (min. hose bend diameter Ø200 mm) and there
it is to be connected to the appropriate connector on top of the unit.
Important! Before putting the unit into operation, the condensate trap of the condensate hose must
be lled with water.
The steam line should be kept as short as possible (max. 4 m while observing the minimum bend
radius of 300 mm (for steam hoses) or 5 x internal diameter (with solid steam pipes), respectively.
Important! Allowance must be made for a pressure loss of approx. 100 Pa per meter steam line
and per 90° elbow.
Important! When deciding on the length and layout of steam hoses, it should be noted that steam
hoses may become shorter and/or longer depending on temperature and age.
The steam hose must be secured to the steam distributor and humidi er steam outlet by means of
hose clamps. Solid steam pipes should be connected to the steam distributor and steam humidier
with short lengths of steam hose secured with hose clamps.
Caution! Do not overtighten the hose clamp on the steam connector of the steam humidier.
Steam lines made of solid pipes (copper or stainless steel) must be insulated over the entire length
to minimize condensate formation (=loss).
DANGER!
Reducing the cross section or the complete closure of the steam line will cause an exces-
sive increase in pressure in the steam cylinder when the unit is operating and could lead to
the risk of scalding accidents. All installations must comply with the following instructions.
When installing make sure the steam line is open over the entire length and through the whole cross
section. Any sealing plugs, adhesive sealing sheets etc. must be removed before connecting the
steam pipe. Reductions in cross section by kinking or crushing must be avoided.
Steam hoses must be prevented from sagging (condensate pockets); if necessary, support steam
hose with pipe clamps, trough, or wall brackets, and install a condensate drain at any low points in
the steam line.
It is not permitted to install a stop valve (e.g. a manually controlled stop valve, solenoid valve,
etc.) in the steam line, due to an inadmissible increase of pressure in the steam cylinder if the valve
is closed during the operation.
Note: If for technical reasons a stop valve is to be installed, the pressure relief valve (available as
accessory) must be installed in the steam line between steam cylinder and and stop valve for safety
reason.
44


Need help? Post your question in this forum.

Forumrules
1

Forum

condair-rs

Reset search

  • why drain hose led to left, is it due to electrical on right side.
    Submitted on 29-8-2022 at 23:32

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Condair RS at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Condair RS in the language / languages: English as an attachment in your email.

The manual is 7,04 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Condair RS

Condair RS User Manual - English - 80 pages

Condair RS User Manual - Dutch - 80 pages

Condair RS Installation Guide - Dutch - 76 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info