Manual Concept VR3120 (page 41 of 99) (English, German, French, Italian, Polish, Spanish)

802865

Zoom out

Zoom in

1/99

80 81

ENEN

VR3100 | VR3110 | VR3120 VR3100 | VR3110 | VR3120

1 Filter strainer cover

2 Dust container button

3 Wall sensor

4 System reset button

5 System upgrade connection

(this connection is for professional use only)

Docking station

1 Power indicator light

2 Signal transmission area

3 Base charging contacts

4 Catch groove

5 Cover plate

6 Cable passage

7 AC adapter socket

8 Winding pin

List of parts

1 Docking station 1x

2 Remote control 1x

3 Wiping cloth 2x

4 HEPA ﬁlter + foam ﬁlter 3x (for VR3100, VR3110 2x)

5 Adapter 1x

6 Cleaning brush 1x

7 Left and right brush 2x

8 HARDFLOOR brush 1x (VR3110, VR3120 only)

CAUTION! Cannot be used on carpets, cleaning may

be interrupted.

When using the HARDFLOOR brush, the robot starts

at the highest power level. The power level cannot be

changed furthermore.

9 CARPET brush 1x

10 Electrically operated water tank 1x (VR3120 only)

11 PET brush 1x (VR3110, VR3120 only)

12 Main brush cover 1x (VR3120, VR3110 only)

suitable for HARDFLOOR and PET brushes

13 Main brush cover with steel wire 1x (suitable for

CARPET brush)

14 Hanging water tank 1x (VR3100, VR3110 only)

KEY FEATURES

Cleaning / ON/OFF

• Press brieﬂy to start or pause cleaning.

• Press and hold for 3 seconds to switch the appliance

on or oﬀ.

• Long press for 15 seconds to force the appliance to

shut down under unusual circumstances.

Charging / Local cleaning

• Press brieﬂy to start or pause charging.

• Long press to start local cleaning.

Indicator light

• Orange (VR3100, VR3110) / turquoise (VR3120):

Normal operation or charging.

• Red: Abnormal condition or low battery.

• Red-orange (VR3100, VR3110) / light blue (VR3120):

The appliance is not connected to the network.

Wi-Fi reset

• Press both buttons simultaneously for 3 seconds.

INSTALLATION

1. Connect the power cord and store the excess

cable length in the cable compartment.

2. Place the docking station against the wall and

connect the power.

Note:

• Provide a space of min. 0.5 m on both sides of the

docking station and min. 1.5 m in front of the station.

• If the power cord is stretched vertically to the ground,

the appliance may pull it out and the docking station

may be switched oﬀ.

• In normal condition, the charging indicator light is on

when switched on. When the appliance is charged, the

indicator remains lit.

3. Do not move the docking station or expose it to

direct sunlight.

Note: Direct sunlight will interfere with the docking

station signal and the appliance may not return to the

docking station properly.

4. Installing the side brush

Make sure the left side brush (L) and right side brush

(R) markings correspond to the L and R markings on

the bottom cover. Push the side brushes L and R until

you hear a “click” sound.

5. Putting the appliance into operation and charging

To switch the robot on, press and hold the button .

If the power indicator light is normally on, charge the

robot in the docking station.

Note: If the appliance does not start due to a low

battery, charge it in the docking station and it will start

automatically. Normally, the appliance can only operate

when the battery level is ≥15 %.

6. Connecting a mobile app (you can skip this step)

Read the instructions for connecting Wi-Fi and connect

the mobile app.

7. Start of cleaning

After switching on the robot, brieﬂy press the button

on the robot or start cleaning using the mobile app

(you can pause the appliance by pressing any button

during use).

Note:

• The sweeping robot cannot be used to remove ﬂuids.

• If the battery charge level is less than 15 %, the

appliance cannot operate. In this case, recharge it.

• If the battery charge level is less than 15 %, the

appliance automatically returns to the docking station.

• Before use, remove various wires (including the

docking station power cord) from the ﬂoor to prevent

outages and damage to objects or wires when the

appliance catches these wires.

• Do not carry the robot during operation. Always use

the manual control designed for controlling the robot.

8. Installing the wiping module

a) Installing the wiping cloth: glue the wiping cloth

straight to the bottom of the water tank.

Model VR3100, VR3110 - Hanging water tank

Model VR3120 - Electrically operated water tank

Note: Clean the wiping cloth after use to keep it in good

condition.

b) Fill the water tank: open the cover and ﬁll the tank

with water.

Model VR3100, VR3110 - Hanging water tank

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Concept VR3120 in the language / languages: English, German, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 2.04 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Concept VR3120 Manual

Product: