Manual Concept VR3110 (page 42 of 99) (English, German, French, Italian, Polish, Spanish)

802864

Zoom out

Zoom in

1/99

82 83

ENEN

VR3100 | VR3110 | VR3120 VR3100 | VR3110 | VR3120

Before ﬁlling with water, remove the dust container

using the handle (VR3120).

Model VR3120 - Electrically operated water tank

c) Install the module:

Model VR3100, VR3110: push the module

horizontally along the back of the robot. The module

is installed in place when you hear a “click” sound.

Model VR3120: insert the dust container into the

water tank and insert the handle into the slot. Then

press and hold the button in the centre of the tank

and push it horizontally along the back of the robot.

The module is installed in place when you hear

a“click” sound.

9. Removing the wiping module

Model VR3100, VR3110: Once the robot has completed

its work, press the latches on both sides, remove the

wiping module backwards, empty the water from the

water tank and clean the cloth (do not move or ﬂip the

robot during cleaning).

Model VR3100, VR3110 - Hanging water tank

Model VR3120: Once the robot has completed its

work, press the button in the middle of the water tank,

remove the wiping module backwards, empty the

water from the water tank and clean the cloth (do not

move or ﬂip the robot during cleaning).

Model VR3120 - Electrically operated water tank

10. Instructions for using the wiping module

• Do not use the wiping module unless supervised.

• For safety, make sure the wiping module is removed

when charging or when not in use.

• Do not attempt to wipe the carpet.

• For a better wiping eﬀect, the wiping module should

be used after sweeping or vacuuming the ﬂoor three

times.

• To reﬁll water or clean the cloth while the appliance

is operating, pause it, remove and reinsert the wiping

module as described in steps 8 and 9. Do not move or

ﬂip the appliance to avoid positioning errors and map

loss.

• The wiping function of the appliance is designed for

wiping and aids deep cleaning. However, it cannot

eﬀectively remove stubborn dirt and thus replace

human power.

USE

ON/OFF

Press and hold the button for 3 seconds, the indicator

light comes on and the appliance starts.

Press and hold the button for 3 seconds while the

appliance is in standby mode, the indicator light goes out

and the appliance switches oﬀ.

NOTE: The appliance cannot be switched oﬀ while it is

being charged.

CLEANING/PAUSE

After starting the appliance, brieﬂy press the button on

the appliance or start the appliance using the mobile app

(press any button to pause the appliance).

Note:

• The robotic vacuum cleaner cannot be used to remove

ﬂuids.

• If the battery charge level is less than 15 %, the

appliance cannot operate. In this case, recharge it.

• If the battery charge level is less than 15 %, the

appliance automatically returns to the docking station.

• Before use, remove various wires (including the

docking station power cord) from the ﬂoor to prevent

outages and damage to objects or wires when the

robot catches these wires.

CHARGING

Automatic mode: The appliance automatically returns to

the docking station after work.

Manual mode: When paused, press the button brieﬂy

to start charging or you can use your mobile app to

charge the appliance. The indicator light ﬂashes when the

appliance is fully charged.

Note: If the appliance does not ﬁnd the docking station,

it will automatically return to its original position. In this

case, place the device manually into the docking station.

COMPLETE AUTOMATIC CLEANING

Once the robot is on, it performs a search, generates

amap and intelligently divides it into areas. Then it sweeps

the areas one after the other properly, eﬃciently and

thoroughly along the wall and plans a curved / S-shaped

cleaning path. After cleaning, the robot automatically

returns to the charging base.

Note: Do not move the robot arbitrarily and often during

cleaning. After moving, place the robot in its original

position. When the robot is on again, it will try to take

a position itself. After successful positioning, the robot

will follow the planned path and continue working. If

positioning fails, the robot cancels the previous task,

creates a map, and cleans up again. Even if it does not ﬁnd

a charging base.

LOCAL TURBO CLEANING

When a local area needs more thorough cleaning, the user

will identify a point on the map in the app, the device will

automatically move close to that point, take that point as

the centre, and clean the area within 1.5 x 1.5 m.

LOCAL CLEANING

If you cannot control the robot using the mobile app,

move the robot manually to the place you want to clean

up. Press the button for 3 seconds and the robot will

perform double cleaning in the area of 2 x 2 m with the

centre in its starting position.

ZONE CLEANING

Use the mobile app to set the size and location of the area

you want to clean up. You can set one or more areas. The

robot will clean in the areas you have set.

RESTRICTED ZONE

Use the mobile app to set up one or more restricted areas.

The robot will not clean in these restricted areas and will

clean in others.

Note: The robot may reach the restricted area due to

positioning errors, sensor errors or other reasons.

• A permanently restricted zone may be invalidated due

to a signiﬁcant change in position of the charging base

and furniture. Therefore, try not to move the robot or

otherwise interfere with its work during cleaning.

• The permanently restricted area will be revoked as

soon as the map is restored.

CLEANING PLANNING

You can set a ﬁxed cleaning time using the mobile app.

The appliance will automatically start cleaning at the

speciﬁed time and will return to the docking station when

completed.

WI-FI RESET

If the mobile phone cannot connect to the appliance

due to a change in router and password conﬁguration

or other reasons, press the button and the button

for 3 seconds at the same time until you hear the “Wi-Fi

has been reset” voice prompt and until the indicator light

turns on blue-violet and ﬂashes slowly.

SILENT MODE

Robot voice messages and planned cleaning will be

suppressed (inactive) during the set time.

CARPET TURBO

When the carpet is detected, the suction force

automatically increases to the highest level. WARNING -

the carpet is correctly detected only with the Carpet

brush.

SETTING THE SUCTION POWER

You can set the suction power to a quiet, standard or high

level using the mobile app.

When the carpet is detected, the suction force

automatically increases to the highest level. WARNING

- the carpet is correctly detected only with the Carpet

brush.

SETTING THE WATER FLOW (only for electrically

operated water tank of model VR3120)

You can set the water ﬂow to a low, standard or high level

using the mobile app.

USING THE REMOTE CONTROL

1. Cleaning planning

2. Moving forward

3. Turning left

4. Local TURBO cleaning

5. Start/pause charging

6. Automatic cleaning / pause

7. Cleaning/pause

8. Turning right

9. Find the robot

10. Setting suction power / water ﬂow

Note: To ensure that all the correct settings are eﬀective,

you must point the remote control at the front of the

robotic vacuum cleaner from close proximity.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Concept VR3110 in the language / languages: English, German, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 2.04 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Concept VR3110 Manual

Product: