Manual Concept VP8290 (page 29 of 59) (English, German, French, Italian, Polish, Spanish)

802917

Zoom out

Zoom in

1/59

If the dust collection bag ll indicator is still red after the bag has been replaced, this may be due to several

causes:

- some of the air passages (hoses, telescopic tube, suction inlet, brush adapter, or other adapters) are

obstructed;

- the motor lter is dirty;

- the air outlet lter is dirty.

Check for each of the possible causes above and eliminate the problem before you start vacuuming. If the

cause of the problem cannot be identied, hand over the product to the nearest service centre. Never use the

vacuum cleaner if the bag level indicator is completely red during operation. The motor could be damaged

irreparably

CLEANING AND MAINTENANCE

You may clean the accessories and the appliance with a wet cloth. Never immerse the appliance in water!

Do not use any aggressive substances for cleaning, such as solvents or abrasives!

REPLACING THE DUST COLLECTION BAG

1. Unplug the product from the mains. Disconnect the hose from the suction inlet and open the appliance

cover.

2. Push the ap on the dust retention bag holder; remove the used dust

retention bag (Fig. 3). Dispose of a paper or SMS dust collection bag. Be

careful not to tear the bag when handling. If the bag is made of fabric,

empty it and close it carefully – it can be used repeatedly.

3. Insert a new or empty dust retention bag by tting the plate in the bag

holder. The bag opening must be aligned with the hose hole in the ap-

pliance cover.

4. Never use the vacuum cleaner without the dust bag installed! If you

forget to insert the dust retention bag or you insert it incorrectly, the

appliance‘s motor may become damaged.

5. Close the cover. Press until you hear a click.

REPLACING FILTERS

• The lters should be cleaned or replaced when they are visibly dirty, or

if the appliance‘s suction power is reduced. Always check the lters after

using the appliance.

• In order to avoid damage to the appliance, do not use it with incorrectly

installed lters.

• Before replacing the lters, disconnect the appliance from the electrical

socket.

• You can buy suitable types of lters from your dealer, or you can order

them from the manufacturer.

CLEANING AND REPLACEMENT OF THE MOTOR FILTER

1. Disconnect the exible hose and open the appliance cover.

2. Pull the dust collection bag out of its holder so that you can access the

motor lter more easily.

Fig. 3

Fig 4

Fig 5

VP 8290

3. Remove the motor lter (Fig. 4). You can clean the lter by tapping it. If the lter is heavily soiled, you may

wash it in lukewarm water and let it dry properly.

4. Insert the cleaned or new motor lter into the appliance and close the cover.

CLEANING AND REPLACING THE AIR OUTLET FILTER

1. Open the air outlet grid in the appliance‘s rear section (Fig. 5).

2. Remove the air outlet lter. You can clean this lter by tapping it, then brushing it with a soft brush. After

this operation is complete, you may clean a very dirty lter by washing and brushing with a soft brush in

lukewarm water with no cleaning agents added. It is important to let the wet parts dry thoroughly. A wet

lter will be damaged by vacuuming! Do not use a hair dryer to dry it!

Note: Wet cleaning may cause more wear and tear of the lter and, consequently, may shorten its service

life.

3. Insert the cleaned or new air outlet lter into the appliance and close the air outlet grid.

TROUBLESHOOTING

Problem Cause Solution

Motor does not run.

Plug inserted into the

mains outlet incorrectly or

insuciently.

Check the plug connection.

The mains outlet is not live. Check for voltage, e.g. by connecting

another appliance.

Motor has stopped

operating.

Improper or insucient air

ow. Motor overheating

fuse activated.

Disconnect the cable from the socket.

Check and release the air suction

and discharge holes; check the lter’s

cleanliness and/or replace the dust bag.

Let the vacuum cleaner cool down.

Front cover cannot be

closed

Dust bag inserted

incorrectly. Check the dust lter installation.

Reduced suction power

Dust bag full or clogged. Replace the dust bag.

Obstructed lter. Clean or replace the lter.

Clogged nozzle, tube, or

hose.

Check and clear the air passage on the

suction and discharge sides.

Vacuum cleaner heats up Slight heating of the vacuum cleaner is normal and cannot be considered

a failure.

OPTIONAL ACCESSORIES

The following appliance accessories can be purchased additionally:

Dust bags (5 units + 2 units of motor lters) Order code SMS9000 Price according to the valid price list

VP 8290

ENEN

5756 VP8290 | VP8291VP8290 | VP8291

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Concept VP8290 in the language / languages: English, German, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 3.01 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Concept VP8290 Manual

Product: