TIMER: When the appliance is running, the operating time can be set using the “timer” button. Set the time to 2 hours, 4 hours, 8 hours, press again to turn off,
the corresponding indicator lights up after the selected time.
Fan speed: Press the fan speed button to change the speed (1-3) and select automatic mode.
Automatic mode: Press the fan speed button to select the fan speed A. The appliance will automatically change the fan speed according to the ambient contaminants.
RESET: The appliance is equipped with a filter replacement alert function. When the filter replacement indicator lights up, replace the filters. Then hold the
button for 3 seconds and the countdown will reset.
INSTALLATION INSTRUCTIONS
• In case of internal dust, such as pollen, the appliance should be placed on the ground. Since pollen, dust, etc. are usually held close to the floor, it is
recommended to place the purifier on a flat floor in the room.
• In order not to block the air inlet and outlet, place the appliance about 30 cm or more away from the left and right sides of the wall, furniture, curtains,
etc. For effective use of the appliance, please keep it at least 20 cm away from the wall behind it.
• Do not place any objects on the top of the appliance (this may cause the appliance to malfunction).
• Note: Do not place magnets or metal objects on the appliance.
• Do not block the air inlet and outlet, for example, do not place any objects on the air outlet. Or on the front side, on the air inlet.
MAINTENANCE
Disconnect the mains supply before cleaning and maintenance.
• Place the filter in a ventilated area so that harmful gases and bacteria on the filter surface can evaporate. Do not expose it to excessive sunlight.
• Do not wash the filter with water.
• Do not work with the filter removed (operation without the effect of removing dust may cause the appliance to malfunction).
• If the appliance is idle for a long time, unplug the power cord (it also consumes power in standby mode).
UVC lamp replacement
• Turn the bottom cover counterclockwise to remove it (Fig. 1).
• Remove the filter.
• Pull the UVC lamp up to remove it and replace it with a new one (Fig. 2).
• Carry out the procedure in reverse to reassemble the appliance.
TROUBLESHOOTING
Common faults, error code description and troubleshooting method.
ProblemCauseRemedy
It is not possible to turn on or press the
button, no responseIs the power cord plugged in?Plug in the power cord.
The odour from the appliance outlet is
unpleasantIs the filter installed correctly?Follow the installation instructions and
precautions.
The purifier runs for a long time, but the air
quality does not improve significantly
The filter indicator is on: this means that the
filter replacement timer has reached the
set value.
After replacing the filter, press the button to restart
Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.
Product:
Forumrules
To achieve meaningful questions, we apply the following rules:
First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.
Register
Register getting emails for Concept CA1020 at:
new questions and answers
new manuals
You will receive an email to register for one or both of the options.
Get your user manual by e-mail
Enter your email address to receive the manual of Concept CA1020 in the language / languages: English, German, French, Italian, Polish, Spanish as an attachment in your email.
The manual is 2.79 mb in size.
You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.
The manual is sent by email. Check your email
If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.
The email address you have provided is not correct.
Please check the email address and correct it.
Your question is posted on this page
Would you like to receive an email when new answers and questions are posted? Please enter your email address.
