663372

Comfortpool ECO 8 Manual

10
Zoom out
Zoom in
Previous page
1/29
Next page
10
3.4 Electrical wiring
Note: Verify the local power supply and the operating voltage of the heat pump. It is recommended to use
the included separate circuit breaker for the heat pump, together with the proper wiring characteristics (see
wiring diagram). The current to the heat pump should only be applied when the filter pump is running.
Further connect the electrical supply to the junction box inside the unit. All ECO heat pumps require single-
phase connection.
Grounding: The circuit breaker protects you against electrical shock caused by a possible short circuit
inside the unit. The heat pump in itself is unable to provide a water flow. Therefore, the heat pump must be
wired electrically together with the filter pump to ensure a water flow while the heat pump is running.
MODEL
POWER SUPPLY (VOLT)
CIRCUIT BREAKER (A)
RUNNING CURRENT (A)
CABLE DIAMETER (mm
2
)
cable length max. 15m
ECO+3
220-240
16
3,3
1,5
ECO+5
220-240
16
4,8
1,5
ECO+10
220-240
20
7,5
2,5
ECO+12
220-240
20
10
2,5
* Values in this table are only guidelines. Please check your local regulations.
3.5 Initial start-up
Startup procedure
After the installation is completed, you should follow these steps:
1. Open bypass valve 1 entirely. Turn on your filter pump, check for water leaks and verify the flow to
and from the pool.
2. Turn on the electrical power supply to the unit, then turn the unit ON with the switch. Slightly close
valve 1 until the heat pump starts.
3. After a few minutes, check if the air leaving the unit is cooler.
4. Allow the unit and filter pump to run 24 hours a day until the desired pool water temperature is
reached. When the set temperature is reached, the unit shuts off. The unit will now automatically
restart (as long as your pool pump is running) when the temperature of the pool water drops more
than 1°C below set temperature.
Several days are needed to bring the temperature of your swimming pool water to its required value.
Covering the pool or the use of ground insulation can drastically reduce this period.
Time delay
The unit is equipped with a built in 3-minute start delay to protect the control circuit components and to
eliminate restart cycling an contactor chatter. This time delay will automatically restart the unit aproximately
3 minutes after each circuit interruption. Even a brief power interruption of the power supply will activate
this delay and prevent the unit from starting until the 3-minute countdown is completed.
… 10 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Comfortpool ECO 8 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Comfortpool ECO 8 in the language / languages: English, Dutch as an attachment in your email.

The manual is 1,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info