778172

CombiSteel 7227.0010 Manual

12
Zoom out
Zoom in
Previous page
1/88
Next page
12
www.combisteel.com
Installation
Installations (refer to Page 4 for parts): Measure the
distance between stove top and the bottom of range
hood. A distance of 27” to 30” is recommended*.
*Due to different ceiling height configurations,
recommended height may not be applicable.
1. You have two ways (A or B) to mount this range hood:
A. Proceed if you would like to mount this range
hood without using the hood-mounting bracket.
1. Using references in Height & Clearance on Page 8 and Mea Measurements and Diagrams on
Page 17, center the hood beneath the cabinet and flush with the front of the cabinet.
2. Draw electrical wires through cabinet access opening and center the hood beneath the
cabinet.
3. From inside of the hood, place screws into the exact center of each knockout hole and secure
to cabinet bottom. Finish tightening all screws until secure. Be careful when using electrical
screwdriver, damage to the range hood may occur. Skip Part B below and proceed to Step 2.
CAUTION: Make certain the range hood is secure before releasing!
B. Proceed if you would like to mount this range hood using the provided hood-mounting bracket.
1. Using references in Height & Clearance on Page 8 and Measurements and Diagrams on
Page 17, mark the leveling point of the hood. Position two mounting screws on the wall, leaving
1/8” space away from the wall. Mounting the hood on wall studs or lumbers is highly
recommended.
2. Attach the hood-mounting bracket to the back of the hood with six screws as shown in
Figure 3.
3. Puncture the knockout wire access hole at the back of the hood and draw the electrical wires
through as shown in Figure 4.
4. Align hood-mounting bracket to the screws on the wall and hook hood into place as shown
in Figure 5. Tighten screws to secure hood to the wall.
CAUTION: Make certain the range hood is secure before releasing!
2. For safety purpose, pre-drilled mounting holes are provided through the back of the hood. For a more secure
installation, use as many mounting holes as needed to secure from the inside of hood.
3. Use 8” round steel pipe (follow building codes in your area) to connect the exhaust on the hood to the
ductwork above. Use silver tape or duct tape to make all joints secure and air tight. Refer to Figure 6.
SAFETY WARNING: Risk of electrical shock. this range hood must be properly grounded. Make sure this is done
by qualified electrician in accordance with all applicable national and local electrical codes. Before connecting
wires, switch power off at service panel and lock service panel to prevent power from being switched on
accidentally.
4. Connect the range hood to a designated standard outlet or cut off the plug and connect three wires (black,
white and green) to house wires and cap with wire connectors.
5. Store excess wires in the wiring box.
6. Drop oil tunnel into recess support near rear of hood. Refer to Figure 8.
… 12 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for CombiSteel 7227.0010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of CombiSteel 7227.0010 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1.44 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info