521991
46
Zoom out
Zoom in
Previous page
1/77
Next page
Installation
Page 46
4.5 Configuring the CSA-300 transceiver
Once all connections have been made the transceiver can be powered and configured for operation. During
configuration information about the vessel on which the transceiver is installed is entered into the transceiver.
It is important this information is entered accurately as it will be broadcast to other AIS equipped vessels and
shore stations.
Once configuration is completed the insta
llation record found at the rear of this manual should be completed
and retained on board the vessel.
4.5.1 Pre configuration checks
To proceed with configuration the following ste
ps should already have been completed:
Th
e transceiver is fixed to the vessel
VHF an
d GPS antennas have been installed and connected to the transceiver
T
he data cable has been connected between the transceiver and junction box
Sh
ips sensors and AIS enabled display equipment have been connected to the junction box
Po
wer has been connected to the transceiver and the transceiver is operational (the display is active).
The following configuration instructions assume the installer is familiar with the CSA-300 us
er interface, details
of which can be found in the Operation section of this manual.
4.5.2 Configure vessel identification information
The transceiver must be configured with information about the vessel on whic
h it is installed prior to operation.
The following information is required:
M
MSI - Vessel MMSI number (Maritime Mobile Service Identity), this can usually be found on the
ships VHF radio license and should be the same MMSI as used for the VHF / DSC radio.
Name - V
essel Name (limited to 20 characters)
Call sign
- Vessel radio call sign (limited to 7 characters)
IMO
No. - Vessels IMO identification number (if applicable)
Dime
nsions giving the location of the GNSS antenna connected to the AIS transceiver (Internal GPS)
Dime
nsions giving the location of the GNSS antenna connected to any external position source
connected to the AIS transceiver
To enter the vessel identification information press the ‘Me
nu’ key and select the ‘Installation’ then ‘Set
identification’ option. You will be prompted to enter a password at this stage, the default password is ‘00000000’
(eight zeros). Refer to section 3.15 for more information on passwords and security
. The vessels MMSI, Name,
Call sign and IMO number can be entered on the scre
en displayed after successful password entry.
www.busse-yachtshop.de | info@busse-yachtshop.de
46


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Comar CSA-300 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Comar CSA-300 in the language / languages: English as an attachment in your email.

The manual is 4,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info