Manual Cola Medea (page 39 of 132) (English, German, French, Italian, Spanish)

668899

Zoom out

Zoom in

1/132

39 MEDEA – MEDEA LUX

Canna

fumaria

Comignolo

antivento

Presa d’aria

esterna

min.100 cm

Camera

ispezionabile

Distanza min 0.2m

Raccordo

fumi

2.4.1Types of installation

Listed below are definitions and requirements for correct installation of an exhaust flue in accordance with Italian

Standard UNI10683:

FLUE : a vertical duct for collecting and expelling, at an appropriate height

from ground, the fumes coming from a single unit and, where permitted,

more than than one.

FLUE technical requirements : it must be fumetight, isolated and insulated

depending on its use;

- it must have a mainly vertical path with axis deviation < 45°;

- it must be at a suitable distance from flammable materials with insulation

or air gap;

- it must preferably have a constant, free and independent round internal

section;

- it is advisable for the flue to have an inspectionable chamber for the

collection of solid materials

- and any condensate, placed under the beginning of the fume duct.

FLUE CONNECTION or DUCT: duct or connection element between the

unit and flue for evacuation of fumes.

DUCT technical requirements: - it must not cross rooms in which the

installation of combustion units is not allowed;

- flexible metal tubes or fibre cement pipes are prohibited;

- the use of counter-sloping elements is prohibited;

- horizontal sections must have an upward slope of at least 3°;

- the length of the horizontal section must be minimal and not more than 3 m;

- there must not be more than 3 changes of direction, without the T union;

- with change of direction > 90° a max. of 2 bends can be used with length in horizontal projection not exceeding 2 m.

- the fume duct must have a constant section and allow the recovery of soot.

CHIMNEY CAP : a device placed on the top of the flue to facilitate the dispersion of fumes into the atmosphere.

CHIMNEY CAP technical requirements : it must have a section equivalent to that of the flue;

- it must have a useful section not less than double the internal section of the flue;

- it must prevent the entry of rain and foreign bodies and ensure the discharge of fumes in any

atmospheric condition;

- it must ensure an adequate dilution of fumes and be positioned outside the backflow area;

- it must be without mechanical means of suction.

The direct discharge of fumes must take place on the roof and not towards closed spaces

( even open air ).

2.5 Brazier and baffle position check

Before lighting the stove make sure the brazier is in the correct position, i.e. fitted in the special slots. Also make

sure the top smoke baffle is properly fitted. A wrongly positioned baffle can result in malfunctioning and excessive

blackening of the glass.

At every stove lighting, check the correct position of the brazier on the brazier holder.

2.6 Electrical connection

Connect one end of the power cable to the rear socket of the stove, and the other to the wall socket.

The voltage supplied by the system must match that specified on the stove dataplate and in the technical data

section of this manual.

During stove idle periods it is advisable to remove the power cable.

- Make sure the electrical system is equipped with an earth and differential switch in accordance

with the

current Regulations.

- The power cable must never touch the stove exhaust pipe.

Antiwind

grille

Flue

connection

Min. distance 0.2 m

Ext. air inlet

min.100 cm 2

Inspectionable

chamber

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Cola Medea in the language / languages: English, German, French, Italian, Spanish as an attachment in your email.

The manual is 9,39 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Cola Medea Manual

Product: