635855

Cointra Thermex IF Manual

5
Zoom out
Zoom in
Previous page
1/12
Next page
6.1. LAYOUT AND INSTALLATION
The EWH should be installed in accordance with the marking on the case and the table below:
Marking
Volume
Layout
RZL, IS-V, IR-V, IQ-V, IF-V,
ID-V
30- 150 litres
Vertical, with branch pipes
downwards
IS-H, IR-H, IQ-H, IF-H, ID-Н
30- 150 litres
Horizontal, with branch pipes
downwards
IS-U, IR-U, IQ-U, IF-U, ID-U
30 - 150 litres
Vertical or horizontal, with
branch pipes downwards or to
the right, respectively
Models IR 5-15 l are placed vertically.
To reduce heat loss in the pipes, it is recommended to install the EWH as close to the
place, where hot water is to be used, as possible.
The EWH is suspended by the case brackets on the anchor hooks fixed in a wall.
Mounting hooks in the wall should exclude spontaneous movement of the EWH brackets on
them.
For the servicing of the EWH, a distance from the protective cover to the nearest surface
in the direction of the axis of the removable flange must be at least:
- 30 centimeters - for models with a capacity of 5-80 litres;
- 50 centimeters – for models with a capacity of 100-150 litres.
WARNING! To avoid damage to the Consumer’s and (or) third parties’ property, when the
hot water supply system is out of order, install the EWH in the rooms provided with floor
waterproofing and drainage to a sewer system. Never place under the EWH things that are
exposed to water. When placing the EWH in unprotected areas, install under the EWH a
protective pallet provided with drainage to a sewer system.
When the EWH is installed in places that are not easily accessible for technical and warranty
maintenance (built-in shelves, recesses, inter-ceiling spaces, etc.), the EWH should be removed
and installed by the Consumer alone, or at his expense.
Note: the protective pallet is outside the scope of the EWH supply.
6.2. CONNECTION TO A WATER SUPPLY SYSTEM
Install the safety valve at the cold water inlet marked with a blue ring by giving it 3.5 - 4
turns and making the connection tight with any waterproof material (flax, FUM tape, etc.)
Do not use the EWH without a safety valve or the other manufacturers’ valves.
When the EWH is in operation, you can watch the appearance of drops from a drain beak
of the safety valve (relieving excessive pressure when water is heated). It is recommended to
connect to a drain beak a rubber or silicon tube of an appropriate diameter to remove moisture.
Connection to a water supply system is made in accordance with Fig. 1 (for models IS-U,
IR-U, IQ-U, IF-U, ID-U in the case of horizontal connection - Fig. 2, while the cold water supply
branch pipe must be below the hot water branch pipe intake) only through copper, metal-plastic
and plastic pipes, and through а special flexible plumbing inlet pipe. It is recommended to supply
water to the EWH through a mud filter mounted in a cold water line (which is outside the scope
of supply).
… 5 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cointra Thermex IF at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cointra Thermex IF in the language / languages: English as an attachment in your email.

The manual is 0,4 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cointra Thermex IF

Cointra Thermex IF User Manual - Dutch - 12 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info