535645
23
Zoom out
Zoom in
Previous page
1/38
Next page
Page 23
800 Series
SECTION 3: CONFIGURATION
Changing The Coin Tubes
and Coin Routing
REMOVING/REPLACING THE TUBES
To remove the coin tubes, remove the acceptor
and then remove the grey, smoked front cover
by pulling out on the left side of the cover at the
notch in the housing. The front cover will
swing forward, exposing the tubes. The tubes
can be removed one at a time by pulling up-
ward. Four slots have been placed in the front
of the changer along the pay-out assembly area
to assist in this procedure. Place a screw driver
into the slot and apply an inward pressure to
free the tube retainer tab whilst pulling upwards
on the tube. Replace the coin tubes by inserting
the dove tail guides into the tube holes and
pushing inward and downward.
ABOUT THE SHIMS
The coin tubes in your COINCO GLOBAL2
®
changer utilise six interchangeable shims to
accommodate variable thicknesses of coins.
These shims are color-coded and are fixed to
the bottom of the coin tubes. Shims are re-
moved and replaced by sliding in or out of the
bottom of the coin tube.
NOTE: Do not reuse shims. Installation and
removal can stress the plastic, causing the
shims to lose their ability to stay firmly in
place.
CHANGING THE COIN ROUTING
After changing the coin tubes, the coin routing
needs to be reconfigured via the Digital Display
using Address “A002”.
This address allows the user to change payout
configuration in the field. This feature only
provides a means for the acceptor to alter coin
routing when different physical payout tubes
have been placed in the changer body.
When address A002 is entered five payout
configurations are available. Selection is
achieved by scrolling up (button B) or down
(button D) to the desired configuration. When
the desired setting is reached, press enter (but-
ton C) to store the selection. The far right
decimal point will illuminate to indicate the
setting has been stored to memory. If the
location has the capability of being program-
mable (Display shows Alt1 for example) press-
ing enter (button C) again will enter program-
mable mode. This will be evident if a value
between “a” and “e” is displayed.
To program a coin to a tube, select the tube by
scrolling to the desired tube, (‘a’ is the first tube
on the left) and drop the coin type to be routed
to the tube. If a coin’s value differs from the
coins currently routed to the tube, all coins
previously routed to the tube with different
values will be rejected. If value “e” is chosen
for a new destination, the coin type dropped will
have its routing changed to the cashbox. Press-
ing enter (button C) again will return to the
second sub address menu, esc (button A) will
always return to the high level address selection
menu.
For correct operation the scaling factor should
be equal to the value of the least coin accepted
E.g. if the least value coin accepted is the GBP
10p after altering the payout configuration the
scaling factor in address A010 should be
changed to 10.
Float modes will be turned off and coin counts
will be cleared for any tube in which all coins
assigned to the tube were not previously as-
signed to the tube and have been assigned
during the current payout configuration session.
23


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Coinco Global 2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Coinco Global 2 in the language / languages: English as an attachment in your email.

The manual is 1,1 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info