586753
8
Zoom out
Zoom in
Previous page
1/15
Next page
Your Detector
Nothing Comes Close to a Cobra
®
Settings
Your Detector
10
English
What to Remember While Using IntelliMute
IntelliMute works with both City and Auto Mute modes.
Whenever your engine revs are below the activation point, the dot next to
the large character on the right side of the display will remain lit. Above the
activation point, the dot will blink twice every two seconds.
If, for any reason, the unit stops sensing your engine’s revs, IntelliMute
will indicate an error and automatically turn Off.
The rev point you set will be stored in the unit’s memory when power is
turned Off and recalled each time the power is turned On.
NOTE
The rev point must be reset if you use your detector in a different vehicle.
NOTE
When initially choosing your IntelliMute activation point, a setting
of approximately 300 to 600 RPMs above idle is recommended.
You can reset the activation point at any time to fit your individual
preferences and driving style.
Setting the IntelliMute Activation Point
Your detector must be installed in your vehicle.
CAUTION
Do not attempt to set the rev point while driving.
Your vehicle should be parked and idling.
IntelliMute must be turned On before setting the activation point. Depending
on whether the unit is in Tone Alert or Voice Alert mode, you will hear a series
of beeps or voice messages as you follow the steps on the next page.
Below Activation Point
X K Ka V S
c
Above Activation Point
X K Ka V S
c
IntelliMute Button
Press and release
To Set the IntelliMute Activation Point
Press and hold
the IntelliMute
button for two
seconds.
Tone
Voice
Visual Display
Two beeps Set Engine Revs None
Rev your engine to
the level you wish
to set (recommend
slightly above idle)
and hold revs steady
for two seconds.
None None Three bars will
flash in succession
At the desired
rev level, press
and release the
IntelliMute
button.
Three beeps IntelliMute Set All three bars flash
three times
Tone
Voice
Visual Display
Four beeps IntelliMute Error,
followed by
IntelliMute Off
E appears
X K Ka V S E
NOTE
If the unit is unable to sense usable pulses within three
seconds or if you do not set a rev point within 20 seconds
of beginning these steps, IntelliMute will indicate an error
and automatically turn Off.
1 2 3
1 2 3
11
Settings
SPX5400_MANL.indd 10-11 1/7/13 10:50 AM
8


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cobra SPX 5400 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cobra SPX 5400 in the language / languages: English as an attachment in your email.

The manual is 2,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info