634407
15
Zoom out
Zoom in
Previous page
1/19
Next page
- 15 -
10.2 CUTTING BLADE
CAUTION: Be sure to disconnect and ground the spark plug wire before working on the cutting blade to prevent accidental
engine starting. Protect hands by using heavy gloves or a rag to grasp the cutting blades. Tip mower as specified in the separate
engine manual. Remove the hex bolt and washer which hold the blade and blade adapter to the engine crankshaft. Remove the
blade and adapter from the crankshaft.
WARNING: Periodically inspect the blade adapter for cracks, especially if you strike a foreign object. Replace when
necessary.
For best results your blade should be sharp. The blade may be resharpened by removing it and either grinding or filing the cutting
edge keeping as close to the original bevel as possible. It is extremely important that each cutting edge receives an equal amount
of grinding to prevent an unbalanced blade. Improper blade balance will result in excessive vibration causing eventual damage to
the engine and the mower. Be sure to carefully balance blade after sharpening. The blade can be tested for balance by balancing
it on a round shaft screwdriver. Remove metal from the heavy side until it balances evenly.
Before reassembling the blade and the blade adapter to the unit, lubricate the engine crankshaft and the inner surface of the
blade adapter with light oil. Insert the key into the blade adapter and Install the blade adapter on the engine crankshaft, push the
washer into the blade adapter and install the blade, Refer to Fig.16A. Place the blade with the part number facing away from the
adapter. Align the washer over the blade and insert the hex bolt. Tighten the hex bolt to the torque listed below:
Fig.16 A
10.3 BLADE MOUNTING TORQUE
Center Bolt 40Nm-50Nm, to insure safe operation of your unit. All nuts and bolts must be checked periodically for correct
tightness.
After prolonged use, especially in sandy soil conditions, the blade will become worn and lose some of the original shape. Cutting
efficiency will be reduced and the blade should be replaced. Replace with an approved factory replacement blade only. Possible
damage resulting from blade unbalance condition is not the responsibility of the manufacturer.
When you change the blade, you must use the original type marked on the blade (Cobra Part No. 263002490 please contact your
local dealer)
10.4 ENGINE
Refer to the separate engine manual for engine maintenance instructions.
Maintain engine oil as instructed in the separate engine manual packed with your unit. Read and follow instructions carefully.
Service the air cleaner as per the separate engine manual under normal conditions.
Clean every few hours under extremely dusty conditions. Poor engine performance and flooding usually indicates that the air
cleaner should be serviced.
To service the air cleaner, refer to the separate engine manual packed with your mower.
The spark plug should be cleaned and the gap reset once a season. Spark plug replacement is recommended at the start of each
mowing season; check engine manual for correct plug type and gap specifications.
Clean the engine regularly with a cloth or brush. Keep the cooling system (blower housing area) clean to permit proper air
15


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cobra MX564SPB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cobra MX564SPB in the language / languages: English as an attachment in your email.

The manual is 0,95 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info