634450
11
Zoom out
Zoom in
Previous page
1/14
Next page
11
Finishing work:
¾ Bring the splitting blade to the lower position (run-in
state).
¾ Releas
e one of the control handles.
¾ Switch the machine off and disconnect the power.
¾ Follow the care and maintenance instructions.
C
C
a
a
r
r
e
e
a
a
n
n
d
d
m
m
a
a
i
i
n
n
t
t
e
e
n
n
a
a
n
n
c
c
e
e
Remove the plug from the power socket before
starting any maintenance or cleaning work.
Wear protective gloves in order to avoid injury to the
hands.
L
Observe the following in order to keep the log splitter in
good working order:
Clean the machine thoroughly after you have
finished using it.
Remove any resin remains on the machine.
Lubricate the splitting column regularly or oil it using
environmentally friendly spray oil.
Check the oil level and change the oil as necessary.
Check hydraulic hoses and
hose connections
regularly for any leaks and firm fitting.
Sharpening the splitting blade
After longer operating periods, for reduced splitting
performance or slight deformation of the cutting edge, grind
the splitting blade or sharpen it with a fine file (remove burrs).
How do I check the oil level?
1. The splitting column must
be in run-in state. Now
remove the
dipstick.
2.
Clean the dipstick and
the oil seal.
3. Replace the dipstick fully
into the oil reservoir.
4. Now remove the
dipstick
again and read off the oil
level.
If the oil level is between the two marking on the dipstick,
there is sufficient oil in the reservoir.
If the oil level is below the lower marking, more oil should
be added with the aid of a clean funnel.
6. Check the oil seal and replace it if it is damaged in any
way.
7. Replace the dipstick into the oil reservoir.
When should I change the oil?
The first oil change should be carried out after 50
operating hours, and then every 500 operating hours.
Two persons are required for this.
Changing the oil:
1. The splitting column must be in run-in state.
2. Now remove the dipstick.
3. Place
a container under the log splitter to catch the ol
d
oil.
The container should have a capacity of at least
4.5 litres.
4. Screw off the drain plug to allow the oil to flow out.
5. Insert the seal
and drain plug again.
6. Pour in the new hydraulic oil (approx.1.5 litres) using
a
clean funnel.
7. Clean the di
pstick and the oil seal.
8. Check the oil seal and replace it if it is damaged in any
way.
9. Replace the dipstick.
Dispose of the old oil properly (local oil disposal point).
The old oil must not be poured into the ground or
drainage system, or mixed with other waste.
Oil dip
s
tick
Shar
pen wedges
upper marking
lower marking
dip stick
11


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cobra LS600V at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cobra LS600V in the language / languages: English as an attachment in your email.

The manual is 4,82 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info