Manual Cobra CS35E (page 22 of 32) (English)

634434

Zoom out

Zoom in

1/32

pinching either the saw chain or the guide bar when the second notch is being made.

- Felling back cut: make the felling back cut (Y) at least 50 mm higher than the

horizontal notching cut. Keep the felling back cut parallel to the horizontal notching cut.

Make the felling back cut so enough wood is left to act as a hinge. The hinge wood

keeps the tree from twisting and falling in the wrong direction. Do not cut through the

hinge.

- As the felling gets close to the hinge the tree should begin to fall. If there is any

chance that the tree may not fall in the desired direction or it may rock back and bind

the saw chain, stop cutting before the felling back cut is complete and use wedges of

wood, plastic, or aluminum to open the cut and drop the tree along the desired line of

fall.

- When the tree begins to fall remove the chain saw from the cutting, stop the motor,

put the chain saw down, and then use the retreat path planned. Be alert for overhead

limbs falling and watch your footing.To complete the felling operation, drive a wedge

(Z) into the horizontal cut.

-Beware of falling branches when the tree starts to move.

b. Cutting branches

•

When using a chainsaw to remove the branches of a tree to the ground, start with the small

branches and those that are not in contact with the ground. Be careful when cutting limbs

under tension as they may be projected too quickly when you suddenly relieve the

tension.

• When you cut the branches, the tree could roll. Always have a backup channel open

in the opposite risk to get away quickly sense. Keep the work area clear to avoid treas-

woodshed

• Never operate a chainsaw arms outstretched. Do not try to cut hard-to-reach areas or

by standing on a ladder. Never work at a height above the shoulders.

c.Cutting logs and planks

• Use a sawhorse or a stable support. Saw still outside of arm sawhorse. The substrate

must be high enough to prevent the tip of the guide bar touching the

ground and the

chain becomes dull.

•

If the saw gets stuck, stop the

machine and remove it from the socket. Raise the

workpiece and change its position. Never attempt to free the trapped saw by pulling the

handle or the electric cable

• Place the saw on one end and put it on at full speed. Advance the saw without force

using the bar spikes as a pivot point. If necessary, reposition the spikes on the timber

to limit the angle of cut.

Note: The diameter of the work piece must not exceed the length of the guide bar

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Cobra CS35E in the language / languages: English as an attachment in your email.

The manual is 4,15 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Cobra CS35E Manual

Product: