538258
7
Zoom out
Zoom in
Previous page
1/9
Next page
Operation
Operation
98
12V DC appliances
The power pack can operate one 12V DC auto, RV, marine, or other portable DC
appliance that draws 10 amps or less from its DC socket. The combined load
must not exceed 120 W, The less combined wattage used, the longer the power
pack will operate before recharging is required.
Operating DC appliances:
1. Check battery status to ensure the battery is fully charged.
2. Open the DC socket.
3. Plug the DC appliance into the DC socket.
4. Turn the DC appliance ON.
5. Recharge the power pack immediately after use.
USB Devices
The power pack can charge or power one USB-chargeable device through its
USB port. Compatible devices include most MP3 players, PDAs, digital cameras,
and camcorders that have internal batteries which can be charged via the USB
port of a desktop/laptop computer.
USB-chargeable devices usually include a special USB cable (not supplied) that
attaches one end to the USB port and the other end to the device.
Jump starting a vehicles engine
You can use the power pack to jump start a vehicle (or boat engine) that has a
12V starting battery using the jump start cables supplied with the unit.
WARNING: Fire Hazard
A reverse polarity connection may cause damage to the unit and/or create a
sparking/explosion hazard. Never allow cables red and black clamps to touch
each other or another common metal conductor. The connection of the cables
to the vehicles battery terminals must be positive to positive (red clamp to
battery “+”) and negative to negative (black clamp to battery “-“ or vehicle
chassis).
NOTE: Carefully follow these instructions for jump starting your vehicle as they
may be different from the instructions supplied with other jump start products
or cables.
To jump start a vehicle:
1. Turn off the vehicle and all accessories.
2. Place the unit on a flat and stable surface near the battery which need to be
started. Ensure that the unit’s jump start power switch is OFF.
3. Connect the red positive (+) clamp of the cables to the positive (+)
terminal of the engine battery.
4. Connect the black negative (-) clamp of the cables to the engine block,
cylinder head, or other stationary heavy metal part of the motor. If the red
“Reverse Polarity” LED illuminates, then reverse polarity has been detected.
Correct polarity must be established before proceeding. Disconnect the
jump starting clamps from the vehicles battery and repeat steps (3) and (4).
5. Switch on the jump start power switch. Before starting the engine, make
sure the jumpstarter pack and the cables are clear of the metal parts and
other moving things.
6. Crank the engine for 5 seconds or until it starts, whichever is first.
WARNING: Fire hazard
Do not try to start the engine for more than 5 seconds. The jump start
feature is designed for short term operation only. Operating the jump
starting feature for more than 5 seconds may cause damage to the unit.
Allow the unit to cool down for at least 3 minutes after each start attempt.
7. Switch off the jump start power switch.
8. Remove the red positive (+) clamp and then the black negative (-) clamp.
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cobra CJS 50 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cobra CJS 50 in the language / languages: English as an attachment in your email.

The manual is 5,12 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info