633035
13
Zoom out
Zoom in
Previous page
1/17
Next page
Alternate Microphones and Installation
19
Nothing comes close to a Cobra
®
Alternate Microphones
and Installation
18
English
Alternate Microphones
and Installation
Alternate Microphones and Installation
To wire the microphone cable to the plug provided, proceed as follows:
1.
Remove the retaining screw.
2. Unscrew the housing from the pin receptacle body.
3. Loosen the two cable clamp retainer screws.
4. Feed the microphone cable through the housing, knurled ring and
washer as shown Fig. 3B.
5. The wires must now be soldered to the pins as indicated in the wiring table.
If a vise or clamping tool is available, it should be used to hold the pin receptacle
body during the soldering operation so that both hands are free to perform the
soldering. If a vise or clamping tool is not available, the pin receptacle body can
be held in a stationary position by inserting it into the microphone jack on the
front panel. The numbers of the pins of the microphone plug are shown in Fig. 4,
as viewed from the back of the plug. Before soldering the wires to the pins,
pre-tin the wire receptacle of each pin of the plug.
Be sure that the housing and the knurled ring of Fig. 3 are pushed back onto the
microphone cable before starting to solder. If the washer is not captive to the pin
receptacle body, make sure that it is placed on the threaded portion of the pin
receptacle body before soldering.
If the microphone jack is used to hold the pin receptacle during soldering operation,
best results are obtained when the connections to pins 1 and 3 are made first and
then the connections to pins 2 and 4. Use a minimum amount of solder and be
careful to prevent excessive solder accumulation on pins, which could cause a
short between the pin and the microphone plug housing.
6. When all soldering connections to the pins of the microphone are complete, push the
knurled ring and the housing forward and screw the housing onto the threaded portion
of the pin receptacle body. Note the location of the screw clearance hole in the plug
housing with respect to the threaded hole in the pin receptacle body. When the housing
is completely threaded into the pin receptacle body, a final fraction of a turn either
clockwise or counterclockwise may be required to align the screw hole with the
threaded hole in the pin receptacle body. When these are aligned, the retaining
screw is then screwed into place to secure the housing to the pin receptacle body.
7. The two cable clamp retainer screws should now be tightened to secure the
housing to the microphone cord. If the cutting directions have been carefully followed,
the cable clamp should secure to the insulation jacket of the microphone cable.
8. Upon completion of the microphone plug wiring, connect and secure the
microphone plug in the transceiver.
Fig. 2 Microphone cable preparation
Fig. 3 Microphone plug wiring
Your Mobile Radio Your Mobile Radio
3
2
4
1
Fig. 4 Microphone plug pin numbers viewed from rear of pin receptacle
13


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cobra 150 GTL DX at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cobra 150 GTL DX in the language / languages: English as an attachment in your email.

The manual is 0,39 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info