599254
58
Zoom out
Zoom in
Previous page
1/290
Next page
58
MONTAGE ECKPANEEL
Damit das Paneel nicht beschädigt wird,
muß eine Decke oder Folie über die Ro-
sette am Eckschrank gelegt werden.
1. Paneel in Befestigungswinkel A auf
Eckschrank setzen und durch Ihre
Schulter abstützen.
2. Potentialausgleichskabel B mit
Schraube C (vormontiert) und
Zahnscheibe D an Thermostat-
grundkörper E befestigen.
3. Zulaufleitungen F mit Wandan-
schlusswinkeln G verbinden - warm
links und kalt rechts. Die Wandan-
schlusswinkel mit einem Schrauben-
dreher öffnen und Dichtheitsprüfung
durchführen.
4. Stromversorgungskabel H der Steu-
erung im Paneel (Adern grau und
schwarz) mit Kabel I des Trafos auf
dem Dach verbinden. Lichtkabel
K der Steuerung im Paneel (Adern
rosa und lila) mit Kabel L des Halo-
genlichts auf dem Dach verbinden.
Kurzes Steuerkabel für Farblicht M
(Adern blau, grün, gelb, rot) mit
Kabel N verbinden.
5. Sensorkabel O (graue Ummanlung,
Adern braun und blau) und langes
Steuerkabel für Dampfgenerator P
(Adern blau, grün, gelb, rot) in Eck-
schrank führen und nach erfolgter
Eckpaneelmontage dort verbinden.
6. Die farbig gekennzeichneten Schläu-
che miteinander verbinden.
7. Eckpaneel vorsichtig ins Eck drücken
und darauf achten, dass alle Leitun-
gen gut hinter dem Paneel verstaut
sind. Das Eckpaneel mit Schraube
R (Zylinderschraube M5 x 12) und
Unterlagscheibe S (A 5,3) sichern,
nicht festziehen.
CORNER PANEL INSTALLATION
Lay a blanket or foil on the escutcheon
to avoid damaging the panel.
1. Position panels in attachment bracket
A on corner cabinet and support
with your shoulder.
2. Attach potential earth bonding cable
B with screw C (pre-fitted) and too-
thed washer D to thermostat body
E.
3. Connect inlet circuits F with wall con-
nection angles G - hot on the left and
cold on the right. Open wall connec-
tion angles with a screwdriver and
perform leakage test.
4. Connect power supply cable H of
control unit in the panel (grey and
black wires) with cable I of transfor-
mer on the roof. Connect light cable
K of control unit in the panel (pink
and lilac wires) with cable L of halo-
gen light on the roof. Connect short
control cable for coloured light M
(blue, green, yellow, red wires) with
cable N.
5. Route sensor cable O (grey shea-
thing, brown and blue wires) and
long control cable for steam ge-
nerator P (blue, green, yellow, red
wires) into corner cabinet and con-
nect them there after corner panel
installation.
6. Connect the colour marked hoses
with each other.
7. Thoroughly press corner panel into
corner, make sure that all leads are
well stowed behind the panel. Secu-
re corner panel with screw R (allen
key screw M5 x 12) and washer S (A
5.3), do not tighten.
MONTAGGIO DEL PANNELLO
ANGOLARE
Per evitare che il pannello possa subire
dei danni è indispensabile posare una
coperta oppure un foglio di plastica
sopra la copertura dell’armadietto
angolare.
1. Applicare il pannello nell'angolo di
fissaggio A sull'armadietto angolare
e tenerlo in posizione poggiandolo
sulla Vostra spalla.
2. Fissare il cavo di compensazione
del potenziale B con la vite C (già
montato) e rosetta dentellata D al
corpo di base del termostato E.
3. Collegare le linee di ingresso F
con gli angolari per applicazione
a parete G - acqua calda a sinistra,
acqua fredda a destra. Aprire
l'angolare per applicazione a parete
utilizzando un cacciavite ed eseguire
la prova di tenuta.
4. Collegare il cavo d’alimentazione
elettrica H della scatola di comando
del pannello (filo grigio e nero) con
il cavo I del trasformatore sul tetto.
Collegare il cavo della luce K della
scatola di comando del pannello (filo
rosa e lilla) con il cavo M della luce
alogena nel tetto. Collegare il cavo
di controllo corto per le luci colorate
M (filo blu, verde, giallo, rosso) con il
cavo N.
5. Inserire nell'armadietto angolare il
cavo sensore O (rivestimento grigia,
fili marrone e blu) ed il lungo cavo di
controllo per generatore di vapore
P (fili blu, verde, giallo, rosso) e
collegarli una volta eseguito il
montaggio del pannello angolare.
6. Collegare reciprocamente i tubi
contrassegnati dai rispettivi colori.
7. Premere il pannello angolare con
attenzione nell'angolo ed accertarsi
che tutte le linee si trovino posate
correttamente dietro il pannello.
Assicurare il pannello angolare con
la vite R (vite a testa cilindrica M5
x 12) e la rondella piatta S (A 5,3)
senza stringere forte.
58


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cleopatra Wellspring 130 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cleopatra Wellspring 130 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 28,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info