599254

Cleopatra Wellspring 130 Manual

16
Zoom out
Zoom in
Previous page
1/290
Next page
16
Vor dem Einbau des Produktes muss
geprüft werden, ob der Fußboden,
auf dem die Dampfkabine installiert
wird, ausreichend nivelliert ist, ob
er das Gewicht tragen kann, und ob
alle technologischen Ausrüstungen
vorhanden sind.
Vor der Ausführung von Reinigungs-
und Wartungsarbeiten muss das
Produkt auf den Energiezustand Null
gebracht werden, d. h. Fehlerstrom-
Schutzeinrichtung (RCD) auslösen.
D e r E i n b a u v o n e l e k t r i s c h e n
Vorrichtungen (Steckdosen, Schalter,
Lampen, usw.) im Badezimmer bzw. im
Installationsraum des Geräts muss nach
den diesbezüglich gültigen Vorschriften
erfolgen.
ACHTUNG:
Kein essigsäurehaltiges Silikon
verwenden.
Durch den Gebrauch von essigsäure-
haltigem Silikon könnten die Acryl- bzw.
Metallteile der Duschkabine beschädigt
werden.
Für das Verfugen zwischen den Elementen
empfehlen wir die Verwendung
von pilzhemmendem Sanitärsilikon.
Dennoch kann es unter Umständen zu
Verfärbungen des Silikondichtstoffes
kommen.
Falls durch Reinigung der Fugen die
Verfärbung nicht zu entfernen ist, müssen
die Silikonfugen ausgetauscht werden.
Silikonfugen sind Wartungsfugen und
unterliegen nicht der Gewährleistung.
ACHTUNG (nur für wannenlos Version):
Ausschliesslich chemikalienfeste Boden-
fliesen oder Duschwanne einsetzen (z.B.
Stahlemail).
Durch austretenden Duftstoff wird ein
nicht chemikalienfester Untergrund
beschädigt.
Die Dampfdusche darf in ihrer
Bauart nicht verändert werden. Nur
Originalersatzteile verwenden.
Stromversorgung:
Der Elektroanschluss darf ausschließlich
vom Elektrofachmann, Ihrem Elektro-
Installateur durchgeführt werden.
Die ges amt e St ro mver sorgun g
erfolgt über einen 230V/N/PE/
50Hz Wechselstromanschluss und
m u s s ü b e r e i n e Fe h l e r s t ro m -
Schutzeinrichtung (RCD) mit einem
Bemessungsdifferenzstrom von ≤ 30 mA
abgesichert werden.
SICHERHEITSVORSCHRIFTEN
Before installing the product check
whether the floor on which the steam
shower cabin is to be installed has
been levelled sufficiently and whether
it can carry the weight and whether all
technological equipment is available.
Set the product to the zero energy state
prior to any cleaning and repair work, i.e.
trigger the RCCB protective switch.
Install electrical devices (sockets,
switches, lamps, etc.) in the bathroom
or in the equipment installation room
according to the relevant regulations.
ATTENTION:
Do not use silicone containing acetic
acid!
Acrylic or metal parts of the shower cabin
can be damaged by the use of silicone
containing acetic acid.
Seals
For the flexible seals between the elements
we advise to use schimmelwerende
silicone kit. Despite this, and dependant
on circumstances, colorchanges in the kit
can happen. If cleaning does not bring
the wanted result, the seals have to be
exchanged. Renewing is not within our
warranty
Caution (nur für wannenlos-Version):
Use only chemical-resistant floor tiles or
a shower tub (e.g. steel enamel).
A non chemical-resistant base is dama-
ged by emitted scents.
The steam shower’s construction must
not be changed. Only original compo-
nents may be used.
Power supply:
The electrical connection may only be
carried out by an electrician, i.e. your
electrical installer. The entire power
supply is realized via a 230V/N/PE/50Hz
AC connection and must be fused via a
2-pole RCCB with a residual current of
≤ 30 mA.
For electrical installation, all applicable
VDE, country-specific and EVU
regulations in their respectively
valid versions must be observed.
All installation and inspection works
must be carried out by an approved
electrician and in accordance with VDE
0100 Part 701. All works at the steam
shower may only be carried out in a de-
energized state!
SAFETY PRECAUTIONS
Prima di procedere all‘installazione
del prodotto ci si deve accertare se il
pavimento di posa sia sufficientemente
livellato, se è adatto a sostenere il peso
previsto e se sono disponibili tutte le
previste apparecchiature tecnologiche.
Prima di procedere ad interventi di pulizia
e di manutenzione è necessario mettere
il prodotto allo stato energetico zero,
cioè, aprire l'interruttore di massima.
L'installazione di dispositivi elettrici (presa
per la corrente, interruttori, lampadine,
ecc.) nel bagno oppure nel locale da
installazione dell'apparecchiatura deve
essere eseguita in conformità con le
relative prescrizioni in vigore.
ATTENZIONE:
Non utilizzare silicone contenente acido
acetico.
Utilizzando silicone contenente acido
acetico vi è il pericolo di danneggiare
parti in materiale acrilico oppure parti
metalliche della cabina doccia.
Per la sigillatura tra gli elementi
raccomandiamo l’uso di silicone
antimuffa per sanitari. Ciò nonostante
si possono verificare macchie o
scolorimenti del silicone sigillante. Nel
caso in cui gli scolorimenti o macchie
non si lasciano eliminare pulendo
semplicemente i giunti, è necessario
sostituirli. I giunti di silicone sono giunti
soggetti a manutenzione e non fanno
parte della garanzia concessa.
Attenzione (nur für wannenlos-Versi-
on):
Impiegare esclusivamente piastrelle da
pavimento resistenti a prodotti chimici
oppure vasca per doccia (p. es. smalto
d'acciaio).
Un fondo base non resistente a prodotti
chimici viene danneggiato da sostanze
odoranti fuoriuscenti.
La struttura della doccia con vapore
non deve essere modificata. Usare solo
ricambi originali.
Alimentazione elettrica:
L’allacciamento elettrico deve essere
eseguito solo da un tecnico (elettricista
esperto). L’intero sistema viene
alimentato a tensione alternata a 230V/
N/PE/50Hz e l’impianto deve possedere
un interruttore di sicurezza per correnti
di guasto (salvavita) bipolare con
corrente di apertura di ≤ 30 mA.
PRESCRIZIONI DI SICUREZZA
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cleopatra Wellspring 130 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cleopatra Wellspring 130 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 28,19 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info