646307
24
Zoom out
Zoom in
Previous page
1/52
Next page
EN 24
Use
CAUTION!
Never aim steam directly at people, animals or plants. This can cause severe scald-
ing.
Only ever hold the device by the handle and not by the attachment while operating
the device as it can become very hot. There is a danger of scalding!
Always work with suf cient lighting.
Make sure that you do not trip over the mains cable while using the device.
Never use the device without water!
Never use the device on cold glass surfaces or at outside temperatures of below
10 °C. The hot steam could cause the glass to shatter.
Always try cleaning rst at a small, inconspicuous spot.
Never direct the steam at one spot for too long.
The water reservoir must not be opened during use!
The device has a a safeguard
(13)
which blocks the steam trigger
(15) so
that it cannot be pressed accidentally. To (de)activate the safeguard, push in
the securing pin.
Water may emerge from the attachment when you rst start using it. This is
normal and does not constitute a defect with the device.
As the pipe in the device has to ll with steam, you may need to press the
steam trigger
(16)
several times when you start using it before steam starts
emerging.
How much steam is emitted depends mainly on the speed and frequency
with which the steam trigger
(15)
is pressed. The faster you press it, the more
steam is emitted. However, this is at the expense of the temperature.
1. Attach the attachment you want to the device (see the "Mounting the Accessories"
chapter) and ll the water reservoir
(18)
(see the "Filling the Water Reservoir" chapter).
2. Insert the mains plug into a properly installed mains socket that is easily accessible.
S
team starts to be generated and the
control lamp
(17)
lights up.
3. Wait until the control lamp goes out. Operating temperature has then been reached
and you can start steam-cleaning: Press the steam trigger
(15) and move the attach-
ment over the
surface to be cleaned as you do so.
If the steam trigger cannot be pressed, the safeguard
(13)
has probably been
activated. Push in the securing pin to release the safeguard.
4. If the control lamp lights up, the temperature has dropped. Let go of the steam trigger
and only press it again once the control lamp has gone out.
5. If the water reservoir is empty, steam will no longer be produced. If you want to top
up the water in the reservoir (see the "Filling the Water Reservoir" chapter) or want to
stop working, pull the mains plug out of the plug socket and allow the device to cool
down completely. Keep pressing the steam trigger if necessary until no more steam
emerges from the device. The water reservoir can then be opened.
6. Empty and clean the water reservoir each time after you use the device (see
below) to prevent deposits in the reservoir and thus damage to the device!
06456_de-en-fr-nl_V1.indb 2406456_de-en-fr-nl_V1.indb 24 03.07.2015 10:28:0403.07.2015 10:28:04
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cleanmaxx Z 06456 - HS101U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cleanmaxx Z 06456 - HS101U in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 0,93 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info