57
Operation and Instructions for Use
NOTE:
• Cut the meat into pieces of around 2.5 cm. Make sure that
there are no bones or sinews in the meat.
• Short term operation: Do not operate the appliance for
longer than 10 minutes and then allow the appliance to cool
for 10 minutes.
10. Feed the pieces of meat (meat paste/ sausage meat or
dough) onto the ller tray and into the ller neck. If you are
mincing meat, place a container under the outlet.
11. Plug the mains plug into a properly installed Schuko socket.
Switch the appliance on with the POWER button.
12. Use the / buttons to select a speed from settings 3 to 5.
13. Start operation with the POWER button.
14. If necessary, feed the meat or dough in with the pusher (30).
WARNING: Risk of injury!
Always use the supplied pusher. Never put your ngers or
utensils into the ller neck!
Making sausages
• You can use natural as well as articial sausage skins.
• If you decide to use natural sausage skins, rst soften them in
water for a while.
• Knot one end of the sausage skin.
• Push the sausage skin over the sausage attachment.
• The sausage meat is pushed through the sausage attach-
ment and the sausage skin is lled.
• Make sure that the sausage skin is lled with slack, since the
sausage expands during boiling or frying and the skin may
rupture.
• If the rst sausage reaches the required length, press the
sausage together at the end of the sausage attachment with
your ngers.
• Rotate the sausage once or twice.
• Until you have developed a routine, you can turn the appli-
ance off after each sausage length.
Shaping cookies
NOTE:
• If you have made a cookie dough, you can form the dough
into different shapes using the cutter (42).
• Use the / buttons to select a speed from settings 1 to 3.
• After you have attached the preassembled worm housing to
the appliance, push the cutter into the cookie maker.
• Set the desired cookie shape.
• Hold the lengths of dough at the outlet with your hand and cut
at the desired length
End operation
1. Switch the appliance off with the POWER button.
2. Disconnect the mains plug.
3. Disassemble all mincer parts.
4. Clean the used parts as described under “Cleaning”.
5. Close the worm housing access with the
cover (13). Turn the cover anticlockwise.
The arrow on the cover must be opposite
the arrow on the appliance. (See the gure
on the right.)
Cleaning
WARNING:
• Disconnect from mains power supply before cleaning. Allow
the mixing bowl to cool.
• Do not submerge the appliance into water. This may lead to
electric shock or re.
CAUTION:
• Do not use a wire brush or other abrasive utensils for clea-
ning.
• Do not use aggressive or abrasive cleaning agents.
• The attachments are not suitable for dishwasher. Heat
and aggressive cleaning agents may warp or discolour the
attachments.
Motor Housing
• Clean the housing only with a damp cloth and a squirt of
washing-up liquid. Dry with a cloth.
Mixing bowl
CAUTION:
There are sensitive electronics in the base of the mixing bowl.
Do not immerse the bowl under water!
• Only use water to rinse out the mixing bowl. You may add a
little detergent.
• Wipe the outside of the mixing bowl with a damp dishcloth.
• Then dry the bowl thoroughly.
Splash guard lid, kneading / stirring attachments and mincer
parts
WARNING: Risk of injury!
The mincing knife is very sharp.
• Parts which have come into contact with food can be rinsed
out with water.
• The seal ring of the splash guard lid can be detached for bet-
ter cleaning.
• Rinse with clean water and dry the parts off.
• Lightly oil the mincer discs with vegetable oil after drying.
Blender accessories
Precleaning
Half ll the blender with water and switch the appliance on for
approx. 10 seconds. Then empty out the water.
Thorough cleaning
WARNING: Risk of injury!
The knives on the knife block are sharp. Proceed with care
when disassembling, cleaning and assembling the parts.
• To clean thoroughly, detach the blender jug.
• Always disassemble the blender jug after use.
• Detach the screw-on base from the blender jug.
• Remove the knife block and the seal ring from the screw-on
base.
• You can clean the glass decanter of the blender jug and the
lid with cap in a bowl of hot water. Rinse with clean water and
dry off.
Seal ring, knife block and screw-on base
• Always rinse off these parts briey with hot water.
• After cleaning and drying all parts, re-assemble your blender
jug in reverse order. Refer to our diagrams on page 4.
Storage
• Clean the appliance as described. Allow the accessories to
dry completely.
• Slide the power cord into the cord compartment.
• We recommend that the appliance is kept in the original pack-
aging if you do intend to use it for long periods.
• Always keep the appliance out of the reach of children in a
dry, well-ventilated place.
Troubleshooting
The appliance does not function
Possible cause:
The appliance has no power supply.
Remedy:
• Check the socket with another appliance.
• Plug in the mains plug correctly.
• Check the main circuit breaker.
Possible cause:
The appliance is faulty.
Remedy:
• Contact our service center or a specialist.
Further possible causes:
Your appliance is equipped with safety switches.
They prevent accidental motor start.
Remedy:
• Check correct position of
- swivelling arm (1)
- mixing container or
- safety cover (3)
- the mixing bowl and
- the splash guard lid (16).
The appliance switches off during cooking
Possible cause:
Cooking with the timer is limited to 15 minutes for safety reasons.
Remedy:
• Restart.
• Work with the timer.
