814219

Clatronic EWB 3798 Manual

11
Zoom out
Zoom in
Previous page
1/58
Next page
EWB3798_IM 05.07. 23
11
• Please note that ice splinters can form and block the ice
cube slide. In this case, after switching on, the mecha-
nism is moved back and forth until it is free again.
- If you want to remove the ice splinters yourself, rst
pull the mains plug out of the socket.
• Note the waiting time of at least 3 minutes if you want to
continue the operation.
• You can change the size of the ice cubes as long as the
compressor is switched off.
ICE FULL Control Lamp (Ice Cube Container Full)
As soon as the ice cube container is full, production stops.
The ICE FULL control lamp lights up. The compressor
switches off.
1. Remove the ice cubes. If necessary, use the enclosed
ice scoop. When removing the ice cube container, some
water drips through the holes at the bottom.
2. After the ICE FULL control lamp goes out, ice cube pro-
duction starts again automatically after a while.
ADD WATER Control Lamp (Water Shortage)
The control lamp indicates when there is not enough water
in the water tank. Ice cube production is automatically
interrupted.
1. Open the lid.
2. Empty the ice cube container.
3. Rell with drinking water as described in “Making Ice
Cubes”. As there may still be residual water in the appli-
ance, observe the MAX marking in the water tank.
4. Reinsert the ice cube container and close the lid.
5. Press the button. The ADD WATER control lamp goes
out. The appliance is in standby mode again. You can
continue with the operation.
Ending Operation
1. Press the button to stop ice cube production. The
control lamp SMALL ashes.
2. Unplug the mains plug from the socket.
3. Remove the ice cube container.
4. Drain the remaining water as described in “Cleaning and
Maintenance”.
5. Leave the lid of the appliance open so that no fungal
cultures or bacteria can form.
Cleaning and Maintenance
WARNING:
• Switch off the appliance before maintenance and cleaning. Pull
the mains plug out of the socket.
• Never immerse the appliance in water for cleaning. It could
cause an electric shock or re.
CAUTION:
• Do not use a wire brush or other abrasive objects.
• Do not use harsh or abrasive cleaners.
• Do not use chemicals, acids, petrol or oil.
Cleaning Programme
With this programme, the water system is rinsed several
times. The process takes about 5 minutes.
Important! The appliance should not be disconnected from
the mains during the cleaning programme.
1. There is an arrow in the water tank below the MAX mark.
Fill approx. 1 litre of fresh water into the water tank, up to
a maximum of below the arrow.
2. While the appliance is in standby mode, press and hold
the button for about 2 seconds. The appliance starts
the cleaning programme. The four control lamps ash
alternately.
3. The appliance automatically switches to standby mode
when the cleaning programme is nished.
4. Drain the water from the appliance. Dispose of the water.
Draining Residual Water
Drain the residual water after each use of the appliance or
at the end of the day.
1. Place the appliance on the edge of a table. Hold a bowl
under the water drain opening.
2. Pull out the plug at the bottom.
3. After the residual water has drained off, put the plug back
in the opening.
… 11 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Clatronic EWB 3798 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Clatronic EWB 3798 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 2.34 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info