323518
32
Zoom out
Zoom in
Previous page
1/54
Next page
ENGLISH
ENGLISH
32
Iron or Steam Brush
Please decide before you start which accessory you need.
Release the plug (13) if necessary by pressing the buttons
and pulling the plug.
Change to the required accessory by inserting the plug (13)
of the accessory.
ޥ NOTE:
On the plug there is an arrow which must be facing
upwards.
Please check whether the plug is fi rmly in place by pulling
on it again. The plug must not become loose.
Steam Jet Button
on the iron: Press the steam jet button (3) to release
a jet of steam. Press the button again to
stop the jet of steam.
on the steam brush: Hold the button down for as long as you
need the steam. Release the button to
stop the jet of steam.
WARNING:
Do not change the accessory while the device is still hot
and therefore under pressure. Steam may be ejected
unexpectedly.
Turn the device off in order to allow it to cool down for 15
minutes.
Water Tank
Press the button (8) if you would like to remove the water
tank (see also illustration A).
This makes it easier to fi ll in water. The contents of the tank
are 1200ml.
Water
Please use only distilled water. Do not use any decalcifi ers!
These will destroy the device!
The following is also unsuitable: Do not fi ll battery water,
water from the clothes dryer and water containing additives
(such as starch, perfume, softener or other chemicals) into the
water reservoir.
This could damage the iron due to residues forming in the steam
chamber. These residues may cause impurities to the fabric
when dropping out of the holes in the soleplate.
Before Initial Use
Clean the ironing base with a slightly damp cloth.
CAUTION: INITIAL USE
Please proceed as follows:
• Connect the iron.
Fill the tank up to the maximum mark. Do not overfi ll!
Close the water tank and place it back in the base.
Connect the base station to a 230 V / 50 Hz socket with
earthing contact.
Turn the switches (11) and (12) on.
Turn the temperature control to
MAX.
The control lamp on
the iron lights up.
Please wait until the control lamp (9) on the base lights
up.
Now press the steam jet button for at least 1 minute.
ޥ NOTE:
This time is needed for the steam to reach the iron.
Keep a cloth ready! During this phase water also
comes out of the soleplate of the iron.
When only steam comes out without any water you can
stop the procedure. Then press the steam jet button
another 2-3 times without touching the clothes that are to
be ironed.
After you have ironed an old but clean cloth a few times,
your station is ready for use.
Operation
Ironing without steam
ޥ NOTE:
Sort out the garments according to their ironing tempera-
tures.
Always set the temperature control to „MIN“ before
connecting the appliance to a power point, or before
disconnecting it.
Place the iron on the rest.
Only connect the machine to a properly installed safety
socket, 230 V/50 Hz.
Turn the switch (12) on.
Set the temperature on the temperature control (4). If you
have sensitive items to iron, please begin with the lowest
temperature.
The control lamp on the iron shows that it is heating up. As
soon as the control lamp goes off the operating temperature
has been reached. Now you can start ironing.
After use always turn the temperature control to „
MIN
(the
control lamp in the handle goes off) and turn the switch (12)
off.
05-DBS 3187 R.indd 3205-DBS 3187 R.indd 32 21.09.2007 10:48:33 Uhr21.09.2007 10:48:33 Uhr
32


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Clatronic dbs 3187 r at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Clatronic dbs 3187 r in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish, Norwegian as an attachment in your email.

The manual is 4,35 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info