364281

Clatronic bz 3233 Manual

16
Zoom out
Zoom in
Previous page
1/84
Next page
20
Dismantling beer dispenser
To clean the beer dispenser and/or to replace the keg,
it is necessary to remove the dispensing unit from the
dispenser. The procedure for this is as follows:
1. When the installed keg is empty,
fi rst remove the CO2 cartridge
from the CO2 chamber by opening
the same and unscrewing the CO2
cartridge holder.
CAUTION FROSTBITE:
• A residual amount of CO2 may still be present in
the cartridge, which suddenly empties and results
in the formation of ice.
NOTE
:
• It is recommended to initially fi t the CO2 cartridge
when preparing the next keg so that the cartridge
cannot accidentally empty if the dispenser lid is
closed without a 5 litre party keg being present in
the dispenser.
2. Press the lid opener.
3. Detach the end of the dispensing
unit from the CO2 feed valve and
remove the keg together with the
dispensing unit using the handle
provided.
NOTE
:
• The silicon sealing ring for the
CO2 feed valve is a wearing
part. If excessive CO2 losses
are noticed during use, replace
the silicon sealing ring with the
supplied spare seal.
Remove the clamps from the rim of the
keg and pull the dispensing unit out of
the keg quickly and evenly. As the beer
tap may not be moist during extraction,
removal may take some effort.
The dispensing unit can now be
cleaned as described in the chapter
"Cleaning" and subsequently installed
on a new keg as described in the
chapter "Preparations".
ATTENTION!
Never remove the dispensing unit from the keg when
pressurised. To change the keg before it is empty,
remove the keg together with the dispensing unit from
the dispenser. Position it in such a way that the beer is
able to fl ow out into a suitable container and pull the tap
handle until no more beer is dispensed.
Cleaning
In order to keep the quality of the dispensed beer at
a consistently high level, it is important to clean the
dispenser thoroughly. The cleaning intervals are specifi ed
in the following.
ATTENTION!
Never use scouring pads, aggressive scouring agents,
acetone, benzine, acids, thinner, vinegar or similar for
cleaning purposes.
Cleaning after each use
Both the collecting tray and drip tray
should be cleaned after each use
of the dispenser to ensure perfect
hygiene.
For this purpose, remove both the
collecting tray and drip tray from the
dispenser and pour the collected beer
into the drain. Subsequently clean
both parts with hot water, using a
small amount of washing/up liquid if
necessary.
ATTENTION!
The parts are not dishwasher proof.
It is recommended to also clean the tube at the front of
the beer tap after each use.
For this purpose, remove the cover at
the front below the beer tap and
remove the tube. Subsequently rinse
out the tube with warm water.
ATTENTION!
If no beer is dispensed over
several days, it is recommended
to thoroughly clean the tube. The
supplied cleaning balloon should be
used for this purpose as follows:
ENGLISH
… 16 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Clatronic bz 3233 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Clatronic bz 3233 in the language / languages: English, German, Dutch, French, Italian, Spanish as an attachment in your email.

The manual is 6,57 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info