Manual Clatronic BS 1308 (page 32 of 58) (English, German, Dutch, French, Italian, Polish, Spanish)

814281

Zoom out

Zoom in

1/58

BS1308_IM 01.08.17

Air Slide

Open the air slide on the hose handle in

order to regulate the airow or to clear any

particles sticking to the nozzle.

Switching off and Winding up the Mains Lead

1. Turn the vacuum cleaner off by the on / off switch and

remove the plug from the socket.

2. Keep the plug in your hand.

3. Press the cable winding button and guide the cable. Hold

the cable to avoid wrapping.

Maintenance

Emptying the Dust Collector

Empty the dust collector once the collected dirt reaches the

MAX marking.

1. Disconnect the mains plug from the wall socket.

2. Disconnect the hose from the hose connection.

3. Press the button (7) to release the dust collector. Remove

the dust collector.

4. Empty the dust collector over a dustbin. To do this, pull

the latch on the dust collector to open the base plate.

5. Then close the base plate again.

6. Attach the dust collector to the appliance. First position it

at the bottom of the appliance and then secure it with the

hook on top.

7. Check that the position of the dust collector is secure by

briey lifting the appliance at its carrying handle.

Filter

Your appliance features 4 lters. The common dust bag

system has been replaced by a transparent dust collector.

The higher ow speed of the collector allows for heavy dirt

and smallest oating particles to be separated from the

“sucked-in air”.

It is thus not necessary to buy dust bags.

Filter Insert

The lters must be cleaned regularly.

CAUTION:

• Never wash the lter in the washing machine.

• Do not use a hairdryer for drying.

• Only use the appliance after the lters have been

installed correctly.

Proceed as follows to remove, clean and reinstall the lter

insert:

1. Empty the dust collector as described previously.

2. Remove the dust collector lid. Turn it anticlockwise in the

direction of .

3. Remove the ne dust lter. Remove the foam insert from

the ne dust lter.

4. Remove the coarse dirt lter from the dust collector.

For this purpose, grasp the lter opening and pull it out

upwards.

5. Use a brush to clean the lters. In case of heavy staining,

clean the lters under running water.

6. Let the lters air-dry completely before retting them!

7. Wipe the dust collector with a damp cloth and then wipe

it dry.

NOTE:

If moisture gets into the rubber seal of the base plate,

carefully remove the seal and dry it as well as the base

plate. Replace the seal.

8. Put the coarse dirt lter back into the collector. Make sure

that the guides are seated in the openings.

9. Insert the foam insert into the ne dust lter. The smooth

side must be visible.

Place the ne dust lter onto the coarse dirt lter.

10. Put the lid back on the dust collector. The guides must

t into the openings. Press it gently and turn it clockwise

until it clicks into position

Check the correct t of the cover. The attened side of the

handle must t over the hose connector.

11. Fit the dust collector in the appliance.

Outlet Filter

The appliance is also equipped with an outlet lter.

It is located on the back of the unit next to the parking aid.

1. Push down the lever (10) and remove the ventilation grille.

2. Remove the lter insert and clean it. You can brush out

the lter. In case of heavy staining, clean the lters under

running water.

3. Reinsert the lter only when fully dried. The guide lugs

must point upwards.

4. Put the ventilation grille back on the appliance. Observe

the guide lugs. The ventilation grid must engage audibly.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Clatronic BS 1308 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 1.95 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Clatronic BS 1308 Manual

Product: