Manual Clatronic BS 1300 (page 31 of 54) (English, German, Dutch, French, Italian, Polish, Spanish)

653899

Zoom out

Zoom in

1/54

Electrical connection

• Before connecting the plug to the wall socket, check wheth-

er the mains voltage is correct. Refer to the information on

the rating plate of the device.

• Connect the device to a certied wall socket only.

Using the Appliance

1. Insert the mains plug into a correctly installed power socket.

2. Turn the device on by the on/off switch by pressing down

the button.

3. Set the “carpet/hard oor” switch, depending on the oor

covering.

4. Vacuum at a steady speed. There is no need to exert pres-

sure.

NOTE:

Pay attention to the range that can be covered with the

cable length!

Air Slide

Open the air slide on the hose handle in order

to regulate the airow or to clear any particles

sticking to the nozzle.

Switching off and Winding up the Mains Lead

1. Turn the vacuum cleaner off by the on/off switch and

remove the plug from the socket.

2. Keep the plug in your hand.

3. Press the cable winding button and guide the cable. Hold

the cable to avoid wrapping.

Maintenance

Dust bag replacement display (10)

Hold the hose up into air. If the display for the vacuum bag

change shows “red”, the dust bag is full. Please change it.

Changing the dust bag

1. Pull the plug out of the socket.

2. Use the opener (13) to open the lid of the dust bag com-

partment.

NOTE:

The lid can be locked in upright position. Do not push the

lid beyond the locking mechanism! Otherwise the mount-

ing could break away.

3. Lift up and remove the dust bag holder. Remove the dust

bag by taking it from the holder.

4. Insert a new bag. Please ensure that the bag is located

correctly in the guide mechanism.

5. Insert the dust bag with the holder into the designated

slot. The bag must be located completely in the dust bag

compartment. Close the cover so that it snaps into place.

Filter

Your appliance has two lters.

Motor protection lter (inlet lter)

The inlet lter is located in the dust bag compartment. The

lter is located vertically in the rear section of the dust housing.

Remove the lter by pulling upwards.

Cleaning the Filter Element

Clean the engine protection lter after 10 dust bag changes. If

necessary, the lter can also be washed in warm water without

any additives. Place it back into place only once it is completely

dry!

Outlet lter (6)

The appliance is also equipped with an outlet lter.

It is located on the back of the device behind the cover.

1. Push the lever towards the left and remove the ventilation

grid.

2. Remove the lter insert and clean it as described above.

3. Once dried completely, reinstall the lter insert.

4. Ret the ventilation grid in the device. Pay attention to

the guide tabs. The ventilation grid must audibly click into

place.

Cleaning

WARNING:

• Before cleaning remove the mains lead from the socket.

• Under no circumstances should you immerse the device in water

for cleaning purposes. Otherwise this might result in an electric

shock or re.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Clatronic BS 1300 in the language / languages: English, German, Dutch, French, Italian, Polish, Spanish as an attachment in your email.

The manual is 2,87 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Clatronic BS 1300 Manual

Product: