320798
24
Zoom out
Zoom in
Previous page
1/42
Next page
ENGLISH
ENGLISH
24
Using the Appliance
1. Unwind the length of cable you require.
CAUTION:
Pull out the cable up to the maximum length indicated
with the yellow mark.
Never pull the cable out up to the red mark as the
cable winding can be damaged.
ޥ NOTE:
If the red mark is visible, pull in the cable with the help of
the cable winding button back to the yellow mark.
2. Insert the mains plug into a correctly installed 230 V, 50 Hz
power socket. Switch the device on by the on/off switch.
3. Set the “carpet/hard fl oor” switch, depending on the fl oor
covering.
4. Set the vacuum power with the vacuum power regulator
(
ț
(Min) to
b
(Max)).
5. Vacuum at a steady speed. There is no need to exert pres-
sure.
ޥ NOTE:
Pay attention to the range that can be covered with the cable
length!
Vacuum power regulator
Low vacuum power: For curtains and delicate fabrics.
Medium vacuum power: For long-pile velour carpets and textile
ooring.
High vacuum power: For sturdy rugs and fl oors.
Air Slide
Open the air slide on the hose handle in order to
regulate the airfl ow or to clear any particles sticking
to the nozzle.
Switching off and Winding up the Mains Lead
1. Turn the vacuum cleaner off by the on/off switch and remove
the plug from the socket.
2. Keep the plug in your hand.
3. Press the cable winding button and guide the cable. Hold
the cable to avoid wrapping.
Nozzle Attachment
Crevice and
jointed nozzle: For vacuuming upholstery, curtains and in
corners and crevices etc.
ޥ NOTE: „2-in-1“ nozzle:
When this is folded together it can be
used as a groove nozzle. If you would like
to use the brush nozzle, pull the brush
section in the direction of the arrow until it
locks in place.
Upholstery nozzle: For cleaning upholstery, curtains etc.
Floor nozzle: To clean carpets or smooth surfaces.
Smooth fl oors: Press down the lever with
the brush symbol with your
foot. The brush is now vis-
ible.
Carpets: Press the lever In the oppo-
site direction. The brushes
are now retracted.
The fl oor nozzle is fi tted with rollers for
improved manoeuvrability.
Parquet brush: For large areas such as parquet, laminate
or tiles etc.
Releasing
the nozzles: Pull these off while turning slightly.
Maintenance
Dust bag replacement display (4)
Hold the hose up into air. If the display for changing the dust bag
appears, the bag is full. Please change it.
Changing the dust bag
Pull the plug out of the socket.
Open the lid of the dust bag compartment by the handle
(11).
Remove the bag by pulling the retainer carefully upwards so
that you have easier access to the bag. Then remove the
dust bag by pulling it upwards.
Insert a new bag. Please ensure that the bag is located
correctly in the guide mechanism. Then reinsert the retainer.
Close the cover so that it snaps into place.
Filter
Your appliance has two fi lters.
Motor protection fi lter (inlet fi lter) (16)
The inlet fi lter is located in the dust bag compartment. The
lter is located vertically in the rear section of the dust housing.
Remove the fi lter by pulling upwards.
Cleaning the Filter Element
Clean the engine protection fi lter after 10 dust bag changes. If
necessary, the fi lter can also be washed in warm water without
any additives. Place it back into place only once it is completely
dry!
Outlet fi lter
The appliance is also equipped with an outlet fi lter. This fi lter is
to be found under the fi lter cover (14).
Press down the lever above the ventilation grille in order to
open the fi lter cover.
Then pull the grille out towards the front. Remove the fi lter
and clean as described above. Please re-insert the fi lter cor-
rectly and close the ventilation grille (until it clicks in place).
05-BS 1274.indd 2405-BS 1274.indd 24 04.02.2009 10:18:33 Uhr04.02.2009 10:18:33 Uhr
24


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Clatronic bs 1274 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Clatronic bs 1274 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish, Norwegian as an attachment in your email.

The manual is 0,97 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info