Manual Clatronic bs 1262 (page 27 of 42) (English, German, Dutch, French, Italian, Polish, Portuguese, Spanish, Norwegian)

318492

Zoom out

Zoom in

1/42

ENGLISH

Cable winding device

Pull out the cable up to the maximum length indicated with the

yellow mark. Never pull the cable out up to the red mark as the

cable winding can be damaged. Said damages are not covered

by the warranty.

Winding

Press the cable (4) winding button and guide the cable. Hold the

cable to avoid wrapping.

Nozzle Attachment

Crevice and

jointed nozzle:

For vacuuming upholstery, curtains and

in corners and crevices etc.

„2-in-1“ nozzle: When this is folded toge-

ther it can be used as a groove nozzle.

If you would like to use the brush nozzle,

pull the brush section in the direction of

the arrow until it locks in place.

Floor nozzle: To clean carpets or smooth surfaces.

Smooth

ﬂ oors:

Press down the lever with the brush symbol

with your foot. The brush is now visible.

Carpets: Press the lever In the opposite direction.

The brushes are now retracted.

Releasing the

nozzles:

Pull these off while turning slightly.

Air Slide

Open the air slide on the hose handle in order to regulate the

airﬂ ow or to clear any particles sticking to the nozzle.

Dust bag replacement display (6)

Hold the hose up into air. If the dust bag change display lights

up, the bag is full. Please change it.

Changing the dust bag

• Pull the plug out of the socket.

• Open the lid of the dust bag compartment by the handle (7).

• Remove the bag by pulling the retainer carefully upwards so

that you have easier access to the bag. Then remove the

dust bag by pulling it upwards.

• Insert a new bag. Please ensure that the bag is located

correctly in the guide mechanism. Then reinsert the retainer.

Close the cover so that it snaps into place.

Filter

Your appliance has two ﬁ lters.

Motor protection ﬁ lter (inlet ﬁ lter)

The inlet ﬁ lter is located in the dust bag compartment. The ﬁ lter

is located vertically in the rear section of the dust housing.

• Remove the ﬁ lter by pulling upwards.

• Clean the engine protection ﬁ lter after 10 dust bag changes.

If necessary, the ﬁ lter can also be washed in warm water

without any additives.

• Place it back into place only once it is completely dry!

Outlet ﬁ lter

The appliance is also equipped with an outlet ﬁ lter. This ﬁ lter is

to be found under the ﬁ lter cover (8).

• Open the ventilation grille by pressing together the lever on

the side of the ventilation grille.

• Then pull the grille out towards the front.

• Remove the ﬁ lter and clean as described above.

• Please re-insert the ﬁ lter correctly and close the ventilation

grille (until it clicks in place).

Cleaning and storage

Cleaning

• Pull the plug out of the socket before cleaning!

• Clean the casing with a dry cloth.

Storage

• Let the iron cool down completely.

• Wind the cable completely.

• If you position the device horizontally: Please insert the hook

of the ﬂ oor nozzle into the parking assistant on the rear of

the device.

• If you place the vacuum cleaner in a vertical position: Please

hang the hook of the ﬂ oor nozzle in the parking aid on the

underside of the vacuum.

Troubleshooting

• The Device Does Not Work.

Remedy:

Check the connection to the mains.

Check the position of the switch.

• The device does not suck up anything.

Possible Cause:

The suction power is set too low.

Remedy:

Check the position of the control switch.

Possible Cause:

The dust bag is full.

Remedy:

Renew the dust bag.

Possible Cause:

The ﬁ lters are dirty.

Remedy:

Clean the components.

Possible Cause:

There is a foreign body in the suction tube or the nozzle.

Remedy:

Check the accessories for foreign bodies.

05-BS 1262 PLUS 27 14.11.2006, 12:54:15 Uhr

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Clatronic bs 1262 in the language / languages: English, German, Dutch, French, Italian, Polish, Portuguese, Spanish, Norwegian as an attachment in your email.

The manual is 1,41 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Clatronic bs 1262 Manual

Product: