580435

Clarion XMD2 Manual

6
Zoom out
Zoom in
Previous page
1/16
Next page
6
XMD1/XMD2
Turning ON the Power and Adjusting the Volume
1) Press the POWER button 4.
∗ To turn off the power, press the POWER button 4 for 1 second or longer.
2) Press the FUNC button 4 and select another operation mode.
Every time the FUNC button 4 is pressed, the display changes
the operation mode as:
Radio ➜ CD ➜ CD changer ➜ Radio
Notes:
• The operation mode not connected to the unit will not be selected.
• If the CD mode is selected when no disc is inserted, the display
flashes “DISC”.
3) Use the volume button 1 to adjust the volume.
w: Increases the volume.
z: Decreases the volume.
∗ The volume level is from 0 (minimum) to 33 (maximum).
Audio Mode Adjustments
Press the A-M button # to select the adjustment mode. The mode
switches as follows each time the A-M button is pressed:
BASS ➜ TREB ➜ BAL ➜ FAD ➜ Previous mode
Adjusting the Bass
1) Press A-M button # and select “BASS”.
2) Press volume button 1 w to emphasizes the bass; press z to
attenuates the bass.
∗ The factory default setting is “0”. (Adjustment range: –6 to +6)
3) When the adjustment is complete, press A-M button # several
times until the function mode is reached.
Adjusting the Treble
1) Press A-M button # and select “TREB”.
2) Press volume button 1 w to emphasizes the treble; press z to
attenuates the treble.
∗ The factory default setting is “0”. (Adjustment range: –6 to +6)
3) When the adjustment is complete, press A-M button # several
times until the function mode is reached.
7. OPERATION
Note:
• Be sure to read this chapter referring to the front diagrams of chapter 2. CONTROLS on page 3.
When this unit is turned on, starting and stopping the engine
of a boat with its volume raised to the maximum level may
harm your hearing.
Be careful about adjusting the volume.
CAUTION
Basic Operations
Adjusting the Balance
1) Press A-M button # and select “BAL”.
2) Press the volume w emphasizes the sound from the right speaker;
press the volume z emphasizes the sound from the left speaker.
∗ The factory default setting is “0”. (Adjustment range: L9 to R9)
3) When the adjustment is complete, press A-M button # several
times until the function mode is reached.
Adjusting the Fader
1) Press A-M button # and select “FAD”.
2) Press the volume w emphasizes the sound from the front speak-
ers; press the volume z emphasizes the sound from the rear
speakers.
∗ The factory default setting is “0”. (Adjustment range: F9 to R9)
3) When the adjustment is complete, press A-M button # several
times until the function mode is reached.
Setting the Z-enhancer
This unit comes with three types of sound tone effects stored in
memory. Select the one you prefer.
∗ The factory default setting is “Z-EHCR OFF”.
Each time you press Z-EHCR button &, the tone effect changes in
the following order.
“Z-ENHANCER 1” ➜ “Z-ENHANCER 2” ➜ “Z-ENHANCER 3” ➜ “Z-
EHCR OFF” ➜ “Z-ENHANCER 1”...
• Z-ENHANCER 1: bass emphasized
• Z-ENHANCER 2: treble emphasized
• Z-ENHANCER 3: bass and treble emphasized
• Z-EHCR OFF: no sound effect
Loudness Effect
In order to turn on/off the loudness effect, use the LOUD button #
for 2 seconds or longer. Every time the LOUD button # is pressed
and held for 2 seconds or longer, the loudness effect switches on
and off.
∗ When the loudness effect is on, the display will show “LD”.
Switching the Clock Display
Every time the DISP button % is pressed, the display will change
between the operation mode and the clock display.
Setting the Clock
1) Press the DISP button % to display the clock display.
2) Press and hold the DISP button % for 2 seconds or longer.
3) Press the SRCH Left button @, then set the current hour.
4) Press the SRCH Right button @, then set the current minute.
5) Press the DISP button %, then the clock is set.
Notes:
• If you select another operation mode while you are setting the clock,
the clock setting operation will be canceled.
• If you remove the vehicle’s battery for a check or repair, the clock
will be reset, so you must set it again.
OK NG
IMPORTANT
Door must be totally closed to prevent water go into the set!
… 6 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Clarion XMD2 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Clarion XMD2 in the language / languages: English as an attachment in your email.

The manual is 1,16 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info