580800

Clarion XC6410 Manual

14
Zoom out
Zoom in
Previous page
1/18
Next page
Owner’s manual & Installation manual
Mode d’emploi et manuel d’installation
Manual de instrucciones y de instalación
XC AMPLIFIERS
AMPLIFICATEURS XC
AMPLIFICADORES XC
XC6210
XC6410
2 XC6210/XC6410
English
Owner’s Manual
INTRODUCTION
The Clarion XC6210 (two-channel amplifier) and XC6410 (four-channel amplifier)
incorporate the following features:
• ConformalCoatedPCBoardthatresistsmold,mildewandmoisturedamage.
• Pulse-WidthModulated(PWM)MOSFETpowersupplyformaximum
performancewithminimaldistortion.
• Remoteturn-onwith"softstart"mutingtopreventturn-on"thump".
• Variablehigh-pass/low-passelectroniccrossoverwitha12dBperoctave
slope(adjustablerange:50Hzto500Hz,500Hzto5kHz-x10).
• Variablebassboostcircuittoreinforcelowfrequencysignals.
• Adjustableinputgainlevelcontrolswithgroundloopisolationtominimizenoise
anddistortion.
• 2-ohmstereostable,4-ohmbridgedstable.
• Corrosionresistantpower,speakerandRCAconnections.
• Speakerlevelinput.(High-levelspeakeroutputtoRCAinputadaptersincluded).
• Lowprofileconstructionwithnon-corrosivealuminumheatsinkforefficientheat
dissipation.
ABOUT THE MANUAL AND WARRANTY
ThismanualdescribesthebasicrequirementstoinstalltheClarionXC6210and
XC6410amplifiers.Theinstallationofthisamplifiercanbequitecomplextoinstall.
Ifyoudonotpossesthenecessaryknowledgeandtoolstoperformthisinstallation,
pleasecontactyourlocalClarionaudiodealer.
Keepallinstructionsandsalesreceiptforfuturereferenceandwarrantyinformation.
TABLE OF CONTENTS
Description ............................................... 3
InputConnectionsandAudioControls .......................... 3
Installation ................................................ 7
MountingPrecautions....................................... 7
WiringPrecautions......................................... 7
XC6410WiringandApplications............................... 8
XC6210WiringandApplications............................... 12
AdjustingtheInputGainControl ............................... 14
SettingtheCrossover....................................... 14
SettingtheBassBoost...................................... 14
FinalSystemCheck........................................ 14
Troubleshooting............................................15
ProductSpecifications....................................... 17
XC6210/XC6410 3
English
Owner’s Manual
DESCRIPTION
TheXC6210andXC6410useaPWMregulatedpowersupplyforsuperiorsound
andoutputwattage.AlloftheconnectionsandcontrolsfortheXC6210andXC6410
areconvenientlylabeledandlocatedononesideoftheamplifier.Toensurethe
bestpossibleelectricalconnections,thepower,speakerandRCAinputsarecorro-
sionresistant.AnadditionalbenefitoftheXC6410istheabilitytocreatea2,3,or
4configuration.Intheeventofcomponentfailureorashortcircuit,theXC6210and
XC6410incorporateprotectioncircuitsandATCfuseprotectiontopreventdamageto
theamplifier.
INPUT CONNECTIONS AND AUDIO CONTROLS
ThefrontpaneloftheXC6410andXC6210containbothconnectionsforRCAand
speakerlevelinputs,alongwiththeaudiocontrolsasshownbelow.
Fig. 1
XC6410
1. CH1RCAInput
2. CH2RCAInput
3. CH3RCAInput
4. CH4RCAInput
5. CH1SpeakerOutput
6. CH2SpeakerOutput
7. CH3SpeakerOutput
8. CH4SpeakerOutput
9. 30AmpATCFuse(Q’ty-2)
10.+12VDCInputBattery
11.RemoteTurn-onInput
12.Ground(ChassisGround)
13.OutputModeSelectorSwitch
(STEREO/CH1Bridged/CH1-2MONO)
14.OutputModeSelectorSwitch
(ST/CH2Bridged/CH3-4MONO)
15.CH1/CH2InputGainControl
16.InputSelect(2CHBB,2CH,4CH)
17.CH3/CH4InputGainControl
18.AutoSense(AutomaticPower
ON/OFF)
19.BassBoost
20.CH1/2CrossoverFrequencySelector
(50Hz~500Hz)
21.CH1/2CrossoverModeSelection
(LowPass,HighPass,FullRange)
22.CH3/4CrossoverFrequencySelector
(50Hz~500Hz),ifx10rangeselected
(500Hz~5kHz)
23.CH3/4CrossoverRangeSelection
(x1orx10)multiplier
24.CH3/4CrossoverMode
Selection(LowPass,HighPass,Full
Range)
25.PowerProtect(StatusLED)
1 3
2
10 11 12
13
14 15 16 17 18 19
20
21 2422 23
4 5
25
9 6 7 8
4 XC6210/XC6410
English
Owner’s Manual
1. CH1RCAInput
2. CH2RCAInput
3. CH1SpeakerOutput
4. CH2SpeakerOutput
5. +12VDCInputBattery
6. RemoteTurn-onInput
7. Ground(ChassisGround)
8. 30AmpATCFuse
9. CH1/CH2InputGainControl
10.AutoSense(AutomaticPower-on/off)
11.BassBoost
12.OutputModeSelectorSwitch
(STEREO/CH1Bridged/CH1-2
MONO)
13.CH1/CH2CrossoverFrequency
Selector(50Hz~500Hz),ifx10Range
Selected(500Hz~5kHz)
14.CrossoverRangeSelection(x1or
x10)multiplier
15.CH1/2CrossoverModeSelection
(LowPass,HighPass,FullRange)
16.PowerProtect(StatusLED)
TheRCAconnectionsarecorrosionresistantforoptimumperformanceandlowsignal
loss.TheRCAconnectorsarelabeledCH1,CH2[forXC6410:CH3,andCH4].
InapplicationswhereRCAsignalsarenotpresent,thespeakerleveloutputfromthe
headunitcanbeused.(High-levelspeakeroutputtoRCAinputadaptersincluded).
XC6210
Red
White
Red
Black
White
Blue
SpeakerleveladaptorcableRCAinputsarefully
balancedandcanacceptRCApreamplevels.
Withspeakerleveladaptorcabletheinputs
willacceptspeakerlevels.(HighLevelRCA
SpeakerAdapterIncluded)
Red
White
Red
Black
White
Blue
SpeakerleveladaptorcableRCAinputsarefully
balancedandcanacceptRCApreamplevels.
Withspeakerleveladaptorcabletheinputswill
acceptspeakerlevels.(HighLevelRCASpeaker
AdapterIncluded)
XC6210/XC6410 5
English
Owner’s Manual
• Input Gain Controls:Allowyoutomatchthesourceunit’soutputvoltagetoachieve
maximumoutputfromtheamplifier.Theamplifiercanaccommodateinputlevels
fromvirtuallyanyheadunitwithaninputrangeof200mVto6.0V.
Regardinghigh-levelinput:Pleaseuseincludedhigh-leveltoRCAadapters.
• Bass Boost:Theaddedboostproducesrich,lowbassfrequenciesthatareusually
difficulttoreproduceinthevehicle/marineaudioenvironment.Bassboostfrequency
(50Hz,0~12dB).
NOTE:XC6410–If2CHor4CHinputisselected,bassboostonlyaffectsCH1/CH2.
If2CHBBinputisselected,bassboostwillaffectCH1/CH2/CH3/CH4.
• Input Select (XC6410 Only) [2CH BB/2CH/4CH]:
2CH BB:UsesCH1/2inputsandhasoutputfromall4channelswithBass
Boost.
2CH:UsesCH1/2inputsandhasoutputfromall4channels.TheBassBoost
willworkonlyonCH1/2.
4CH:Usesall4channelinputsandhasoutputfromall4channels.TheBass
BoostwillworkonlyonCH1/2.
• Output Mode Selector Switch:
XC6210
STEREO:(Commonapplications)InputofRCAintoCH1/CH2willresultinspeaker
outputofCH1/CH2.
CH1 BRIDGED:(Limited/Specialapplications)InputofRCAintoCH1willresultin
speakeroutputofCH1/CH2.
CH1-2 Mono:(Subwooferapplications)SummedinputofRCAintoCH1/CH2will
resultinspeakeroutputofCH1/CH2orCH1+andCH2-.
XC6410 CH1-2
STEREO:(Commonapplications)InputofRCAintoCH1/CH2/CH3/CH4willresultin
speakeroutputofCH1/CH2/CH3/CH4.
CH1 BRIDGED:(Limited/Specialapplications)InputofRCAintoCH1willresultin
speakeroutputofCH1/CH2.
CH1-2 Mono:(Subwooferapplications)SummedinputofRCAintoCH1/CH2will
resultinspeakeroutputofCH1/CH2orCH1+andCH2-.
(XC6410) CH3-4
STEREO:(Commonapplications)InputofRCAintoCH1/CH2/CH3/CH4willresultin
speakeroutputofCH1/CH2/CH3/CH4.
CH2 BRIDGED:(Limited/Specialapplications)InputofRCAintoCH2willresultin
speakeroutputofCH3/CH4.
CH3-4 Mono:(Subwooferapplications)SummedinputofRCAintoCH3/CH4will
resultinspeakeroutputofCH3/CH4orCH3+andCH4-.
• Auto Sense (ON/OFF)
OFF: (commonapplication)Whensourceunitremoteturn-onwireavailable.
ON: (factoryradioapplication)MustuseincludedRCAinputadapters.
Note:Inthissetting;donotconnectanythingtoREMterminal.
6 XC6210/XC6410
English
Owner’s Manual
XC6410-ElectricalConnection
XC6210 - Electrical Connection
Remote Turn-On
CH4 Speaker (+)
CH4 Speaker (-)
CH1 Speaker (-)
CH1 Speaker (+)
CH2 Speaker (+)
CH2 Speaker (-)
CH3 Speaker (-)
CH3 Speaker (+)
F
U
S
E
XC6210/XC6410 7
English
Owner’s Manual
INSTALLATION
ThissectionsuggestsMountingandWiringPrecautionsforinstallingtheClarion
XC6210orXC6410.Ifyoudonotpossesthenecessarytoolsandinstallation
experience,donotattempttoinstalltheseamplifiers.Instead,contactyourlocal
Clarionaudiodealertoperformtheinstallation.
MOUNTING PRECAUTIONS
Priortomountingtheamplifier,makesureitissafetomounttheamplifierindesired
location.Failuretodosocanresultinseriousdamagetothevehicle/boat.Extra
careandattentionisnecessaryinmarineinstallationsduetotheuncertaintyof
waterconditionsenvironment.Stainlesssteelhardwareisrecommendedformarine
applications.
Additionalprecautionsandsuggestions:
1.Forthemostefficientcooling,mounttheamplifiersocoolairrunsalongthe
lengthoftheheatsink,ratherthanacrossthem.Toincreaseairmovementand
circulation,acoolingfancanbeinstalled.
2.Mounttheamplifieronarigidsurface;avoidmountingtosubwooferenclosuresor
areaspronetovibration.
3.Priortodrillingandmounting,makesuretheproposedmountingholeswillnotcut
intothefueltank,fuellines,brakelines,electricalwiring,orthebodyofvehicleor
boat.
4.Donotmounttheamplifierwhereitissusceptibletowater.
WIRING PRECAUTIONS
Readallofthewiringprecautionspriortomakinganyconnections.Ifyouareunsure
and/ordon’thavethenecessaryinstallationhardware,contactyourlocalClarion
audiodealertoperformtheinstallation.
1.Beforeyoubegintheinstallation,makesurethevehicleisnotrunningandisin
theOFFposition.
2.Disconnectthenegative(-)leadofthebattery(orbatteries)beforemakingany
powerconnections.
3.Whenmakingconnections,besurethateachconnectioniscleanandsecure.
Insulatefinalconnectionswithelectricaltapeorheatshrinktubing.Failuretodo
somaydamageyourequipment.
4.Agoodgroundiscriticalfortheperformanceoftheamplifier.Agroundwire
shouldberundirectlyfromthebatterytotheamplifier(marineapplication).Use
blackinsulated10-gaugeorlargerwirefortheamplifier’sground(-)powerlead.
5.Addafuseholderandfuseatthepositive(+)terminalofthebattery.
Thefuseratingshouldequalthetotalcurrentconsumptionatfulloutputofthe
amplifier(s).Useredinsulated10-gaugeorlargerwirefortheamplifier’spositive
(+)powerlead.Donotinstallthefuseuntilthecompleteinstallationhasbeen
performed.
6.Whenreplacingtheamplifier’sfuse,alwaysuseonehavingthesameamperage
rating.Substitutingahigherratedfuseoraslow-blowtypecanresultinserious
damagetotheamplifier.
8 XC6210/XC6410
English
Owner’s Manual
7.Whencreatingpassageholesforpowercables,RCA’scables,andspeakerwires,
usegrommetstoeliminateanysharpedgescreatedduringdrilling.Thiswill
protectthewirefrombeingdamagedandpreventashortcircuit.
8.Extracablecancausesignallossandactasan“antenna”fornoise.Useonly
high-qualityRCAcablesthatarenolongerthannecessary.
9.Inmultipleamplifiersystems,itisrecommendedtousearelayontheremote
turn-onleadoftheradio.
XC6410 WIRING AND APPLICATIONS
TheClarionXC64104-channelaudioamplifiercanbeusedinavarietyofsystem
applications.Hereareafewexamplestohelpplanyourowninstallation.
CH1 Speaker
CH3 Speaker
CH2 Speaker
CH4 Speaker
SETTING PANEL (Enlarged picture)
Fig. 4
4-Channel Full Range Stereo System
Inthisapplication,theXC6410isusedasa4-channelamplifiertodrivefourfull
rangespeakersinstereo.Note the switch settings.
XC6210/XC6410 9
English
Owner’s Manual
CH1 Subwoofer 2Ω or 4Ω
CH3 Speaker System
CH2 Subwoofer 2Ω or 4Ω
CH4 Speaker System
SETTING PANEL (Enlarged picture)
Fig. 5
2-Channel High-Pass, 2-Channel Low-Pass
Inthis4-channelsystem,theXC6410drivesapairofcomponentspeakersand a pair
ofsubwoofers.Note the switch settings.
10 XC6210/XC6410
English
Owner’s Manual
Subwoofer
4Ω only
CH4 Speaker System
CH3 Speaker System
SETTING PA NEL (Enlarged picture)
Fig. 6
2-Channel Stereo System with Low-Pass Bridged Mono Channel
TheXC6410canalsobeusedtodriveapairofcomponentspeakersandasingle
monosubwooferusingonesetofRCA’s.Note the switch settings.
XC6210/XC6410 11
English
Owner’s Manual
Bridged CH1/CH2
Speaker System
4Ω only
(Note: Output is from Input CH1)
Bridged CH3/CH4
Speaker System
4Ω only
(Note: Output is from Input CH2)
SETTING PANEL (Enlarged picture)
Fig. 7
2-Channel High Power System Speakers
TheXC6410canbesetupasa2-channelhighpoweramplifiertodriveapairof
speakers(stereo).Note the switch settings.
12 XC6210/XC6410
English
Owner’s Manual
XC6210 WIRING AND APPLICATIONS
TheClarionXC62102-channelaudioamplifiercanbeusedinavarietyofsystem
applications.Hereareafewexamplestohelpplanyourowninstallation.
Fig. 8
2-Channel Full-Range Stereo System
Inthisapplication,theamplifierisusedinstereoanddrivestwofull-rangespeakers.
Note the switch settings.
CH1
Full Range Speaker
CH2
Full Range Speaker
XC6210/XC6410 13
English
Owner’s Manual
Fig. 10
Bridged - Mono Subwoofer System
Inthisapplicationtheamplifierisbridgedformonooperationtodriveasubwoofer.
Note the switch settings.
Subwoofer
4
Ω only
Fig. 9
Subwoofer Stereo System
Inthisapplication,theamplifierisusedtodrivetwosubwoofers.
Note the switch settings.
CH1
Subwoofer
2Ω or 4Ω
CH2
Subwoofer
2Ω or 4Ω
14 XC6210/XC6410
English
Owner’s Manual
ADJUSTING THE INPUT GAIN CONTROL
Aftercompletingtheinstallation,followthesestepstosettheInputGainControl.
1.SetInputGainControltoMIN(counterclockwise).
2.Poweronsource.SetallToneorEqualizationControlsto“flat”positionsandset
Loudnessoff.
3.PlayaCD,settheSourceVolumeControlto75%ofmaxlevel.
4.SlowlyadjusttheInputGainControlofamplifier.Stopwhenyouhearaslight
distortionofaudio.
NOTE: Iftheaudiosystemusesanequalizer,setitsfrequencycontrolsto“flat”
positions.
SETTING THE CROSSOVER
TheClarionXC6210andXC6410featurefullyadjustablehighandlowpass
crossovers.Tosetthecrossover,followthesesteps.
1.UsingtheCrossoverModeSwitch,selectthedesiredmode:LOWforLowPass,
HIGHforHighPassorFULLforFullRange.
2.UsingtheFREQ(Hz)SelectionControl,selectthedesiredfrequency.Ifthe
desiredfrequencyexceedstherangeoftheFREQ(Hz)SelectionControl,slide
theCrossoverFrequencyMultiplierSwitchtox10.
•Forexample,50Hzx10=500Hzor500Hzx10=5kHz
NOTE:x10MultiplierisavailableonXC6210andXC6410(onlyonCH3/CH4)
SETTING THE BASS BOOST
1.SetBassBoostto0dB(counterclockwise).
2.Listentoavarietyofmusicstyles(e.g.Rock,Rap,etc.)andslowlyadjustthe
BassBoostcontrol(clockwise)torealizethebestbassresponse.
FINAL SYSTEM CHECK
1.Poweronthesourceunit.SlowlyincreasetheVolumeControlandlistento
theaudio.Ifthereisnoaudioorifyouhearanystatic,distortion,pleasecheck
theconnectionsandrefertotheTroubleshootingsection.Dependingonyour
systemdesign,thelevelsmaybecomequiteloudevenatlowVolumeControl
settings.Untilyougetan“audiofeel”ofthesystem’spower,usecarewhen
adjustingcontrols.
2.Check“Source”Balance(LeftandRight)andFader(FrontandRear)toensure
properinstallation.
3.Increasethevolumeandverifythattheamplifierreproducesaudio(atfull
frequencies)withoutdistortion.Ifyouheardistortion,checktheconnectionsand
verifythattheInputGainControlissetproperly.
XC6210/XC6410 15
English
Owner’s Manual
TROUBLESHOOTING
Problem
NoAudio.Amplifiernotpoweringon.(LEDturnedoff)
Solution
Remoteturn-onvoltage.Checkremoteconnectionsatamplifierand
sourceunit.
Blownamplifierfuse.Replacewithnewfuse(samerating).
Powerwiresnotconnected.Checkpowerandgroundwiringatamplifierand
atbattery.
Speakerleadsshorted.Checkspeakercontinuitytoground,itshouldnotshow
acommonground.
Speakersnotconnectedorareblown.Checkspeakerconnectionsatamplifier,
measurecoilimpedance.
Problem
Audiocyclesonandoff.
Solution
Thermalprotectioncircuitsareshuttingamplifieroff.Checklocationfor
adequateventilation;consultanauthorizedClarionaudiodealer.
Problem
Distortedaudio.
Solution
InputGainisnotsetproperly,ordamagedspeakercones.ReviewSettingGain;
inspecteachspeaker.(i.e.checkconnection,speakerimpedance,etc.)
Problem
Audiolackspunch.
Solution
Speakerswiredincorrectly,whichcausescancellationofbassfrequencies.
Checkpolarityofwiresfromamplifiertoeachspeakerasdefinedbythe
systemdesign.
16 XC6210/XC6410
English
Owner’s Manual
Problem
Amplifierfusekeepsblowing.
Solution
Incorrectwiringorshortcircuit.Reviewinstallationandcheckallwiring
connections.
Problem
Whiningortickingnoiseintheaudiowithengineon.
Solution
Amplifierispickingupalternatornoiseorradiatednoise.Lowerinput
gain;moveaudiocablesawayfrompowerwires.Checkpowerandground
connectionsonamplifier;checkalternatorand/orvoltageregulator;testforweak
battery,checkpowerandgroundconnectionsofbattery.
XC6210/XC6410 17
English
Owner’s Manual
XC6410
FrequencyResponse 20Hz~20kHz
CrossoverFrequency(Low,High,Full) Variable50Hz~500Hz,*(x10,500Hz~5kHz)
LowLevelInputSensitivity 200mV~6.0V
Max.PowerOutput@4Ω 600W(300Wx2)
RMSPowerOutput@4Ω 85Wx4@1.0%THD
RMSPowerOutput@2Ω 125Wx4@1.0%THD
RMSBridgedPowerOutput@4Ω 250Wx2@1.0%THD
Fuse 30Ax2
Dimensions(WxHxD) 222mmx55mmx174.2mm
8.74inx2.17inx6.86in 
PRODUCT SPECIFICATIONS
PowerOutput: 85Wx4RMS[4Ω@
14.4V1%THD+N]
SignaltoNoiseRatio:80dB(Reference:1Winto4Ω)
XC6210
FrequencyResponse 20Hz~20kHz
CrossoverFrequency(Low,High,Full) Variable50Hz~500Hz,*(x10,500Hz~5kHz)
LowLevelInputSensitivity 200mV~6.0V
Max.PowerOutput@4Ω 350W(350Wx1)
RMSPowerOutput@4Ω 85Wx2@1.0%THD
RMSPowerOutput@2Ω 125Wx2@1.0%THD
RMSBridgedPowerOutput@4Ω 250Wx1@1.0%THD
Fuse 30Ax1
Dimensions(WxHxD) 161.2mmx55mmx174.2mm
6.35inx2.17inx6.86in 
PowerOutput: 85Wx2RMS[4Ω@
14.4V1%THD+N]
SignaltoNoiseRatio:80dB(Reference:1Winto4Ω)
*:x10MultiplierisavailableonXC6210andXC6410(onlyonCH3/CH4)
Clarion Corporation of America
AllRightsReserved.Copyright
©
2012ClarionCorporationofAmerica
PrintedinChina/ImprimeauChiné/ImpresoenChina
12/2012 XC6210/XC6410
… 14 …


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Clarion XC6410 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Clarion XC6410 in the language / languages: English as an attachment in your email.

The manual is 1,2 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info