659139
2
Zoom out
Zoom in
Previous page
1/2
Next page
NAMES AND FUNCTIONS OF PARTS
Interface Box (Equipment) Front Panel
Calibration Indicator [CAL]
* The indicator will light up in green (for about 5 sec-
onds) during image capture.
UART terminal [DATA]
* Connect the serial cable.
RCA terminal [VIDEO]
* Connect the RCA cable.
Interface Box (Equipment) Rear Panel
Power indicator [POWER]
* The indicator will light up in red when power is ON.
USB terminal [USB]
* Connect the USB cable.
Reset switch [RESET]
* This is used when resetting the equipment.
Use a thin rod to press the switch for two or
more seconds.
CAUTION
Do not use this equipment close to a mobile phone or wireless device.
The radio waves from the mobile phone or wireless device may result in noise
and malfunction.
OPERATING METHOD
Start up the equipment.
5.
Start up a notebook PC and install the software on the enclosed application
CD.
6.
Connect the notebook PC and camera ECU to the equipment using the en-
closed cable.
When the USB cable is connected, power is supplied from the PC and the power
indicator lights up in red.
See the cabling instructions and connect the cables between the equipment cor-
rectly.
Advice
7.
Start up the camera ECU.
8.
Perform the operations with the application software installed in the notebook
PC.
See the application software manual in the notebook PC on how to use the appli-
cation software.
Advice
CAUTION
Do not supply power other than the USB bus power to the equipment.
This may result in fire and faults.
Terminating this equipment
1.
Check that access to the equipment and camera ECU has been stopped.
The checks to be conducted when access is stopped are as follows.
3
Check that the calibration indicator (green) has been turned off.
4
Check that serial communication in the application has been stopped.
Advice
2.
Use the application software to disconnect the camera ECU from the equip-
ment.
See the application software manual in the notebook PC on the shutdown proce-
dure.
Advice
3.
Disconnect the USB cable.
The power of the equipment goes OFF and the power indicator (red) goes off.
4.
Disconnect the RCA cable and serial cable.
CAUTION
When disconnecting the USB cable, check that the calibration indicator (green)
goes off.
WIRING AND CONNECTIONS
Preparations
Equipment Enclosed cables
6
Interface Box (Equipment) ...................... 1
Notebook PC (
see below for compatible OS)
...... 1
Camera ECU (Sold Separately) ................. 1
Car-mounted Camera (Sold Separately) .... 4
2
USB Cable ............................................. 1
3
RCA Cable ............................................ 1
4
Serial Cable ........................................... 1
* The notebook PC, camera ECU and car-mounted cameras are sold separately.
* Make sure only the enclosed cables are used.
Notebook PC Compatible OS / Display Resolution
Compatible OS
Windows 7
Professional SP1 32 bit / 64 bit Japanese
version, 32 bit English version
Windows 8.1
Pro 64 bit Japanese version
Display Resolution
XGA (1024 x 768) & above
* Compatible OS are operating systems that have been internally verified to work normally. However, opera-
tions may differ depending on the type of PC and the application software installed in the PC.
How to Connect the Cables
6 SurroundEye Interface Box
(Equipment)
Back Panel
Notebook PC
6 SurroundEye Interface Box
(Equipment) Front Panel
Camera ECU and
car-mounted camera
Connect to the RCA terminal [VIDEO]
3 RCA cable
4 Serial Cable
Connect to the RCA terminal [RCA connectors]
Connect to the UART terminal [4 connectors]
Connect to the UART terminal [DATA]
Connect to the USB port [USB]
* USB B MALE CONNECTER
Connecting to a USB port
* USB A MALE CONNECTER
2 USB cable
Yellow Green
Gray
Gray
Yellow
White
Camera
ECU
TROUBLESHOOTING
Please follow the following troubleshooting procedures in case of any problems.
Consult your dealer if you cannot resolve the issue on your own.
Symptom Reason Solution
There is no power.
The power indicator
is not lit.
The USB cable is
not connected cor-
rectly.
Please see the cabling instructions and
connect the cable correctly.
Image cannot be
captured in the note-
book PC.
The captured image
is distorted.
The RCA cable is
not connected cor-
rectly.
Please see the cabling instructions and
connect the cable correctly.
Serial communication
does not work.
The serial cable is
not connected cor-
rectly.
Please see the cabling instructions and
connect the cable correctly.
The application does
not work.
The various cables
are not connected
correctly.
Please see the cabling instructions and
connect the cable correctly.
The application does
not work.
The micro-computer
is malfunctioning
due to noise etc.
Use a thin rod to press the reset switch
for two or more seconds.
Start up the application again.
The equipment gets
abnormally hot.
The internal elec-
tronic parts may be
faulty.
Unplug the USB cable immediately,
switch off the power supply and con-
sult your dealer.
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Clarion UG-2176A at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Clarion UG-2176A in the language / languages: English as an attachment in your email.

The manual is 0,84 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info