537064
6
Zoom out
Zoom in
Previous page
1/13
Next page
6
NK1U
English
Installing the Car Dock
Note:
Install the Car Dock in a location where it does not
interfere with vehicle operation.
Install the Car Dock in a location where it does not
interfere with airbags and other safety devices.
Installing
1. There is tape affixed to the bottom of the Car
Dock, which is covered by a protection sheet.
Without removing the protection sheet, place
the Car Dock on the dashboard of the vehicle
to determine the best installation position.
Note:
Select a location where the ClarionMiND can be
attached to and removed from the Car Dock without
hitting the windshield of the vehicle. For information
about attaching and removing the ClarionMiND, see
Attaching and Removing the ClarionMiND (P. 9).
2. Remove the protection sheet from the bottom
of the Car Dock and then affix the Car Dock to
the dashboard of the vehicle.
Note:
Use a dry cloth to wipe the installation location free
of dust and oil.
It takes about 24 hours for the adhesive tape to
achieve full adhesion.
3. Use the supplied tapping screws to secure the
two locations at the back of the Car Dock to
the dashboard.
4. Use the hex wrench to loosen the Car Dock's
hex head screw to the point of maximum tilt.
Note:
If the Car Dock does not tilt, you will not be able to
tighten the tapping screws with a screwdriver.
Fully loosen the hex screws until the Car Dock is
fully tilted. However, note that loosening the hex
screw too much can cause the hex screw to come
out.
5. Use the supplied tapping screws to secure the
two locations at the front of the Car Dock to
the dashboard.
6. Adjust the tilt of the Car Dock to the desired
angle and then tighten the hex screw to
secure it.
* Hex screw tightening torque: Use a range of 4 Nm
to 5 Nm (Approximately 0.4 kgfm to 0.5 kgfm) as
a general guide.
Note:
You can adjust the tilt angle of the Car Dock within a
range of 10 degrees forward, 25 degrees back, and
5 degrees horizontally.
Car Dock
Dashboard
ClarionMiND
Dashboard
Windshield
Dashboard
Protection
sheet
4 Tapping screws
5 Hex wrench
25°
4 Tapping screws
6


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Clarion NK1U at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Clarion NK1U in the language / languages: English as an attachment in your email.

The manual is 1,09 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info