659138
2
Zoom out
Zoom in
Previous page
1/2
Next page
HOW TO INSTALL
Installation Precautions
Be sure to read the Safety Precautions prior to installation and follow them throughout.
Installation Precautions
1 Camera ECU box
2-2 Mounting brackets
4-3 M5 × 12 mm hex bolts with washers
Precautions for Installing Mounting Brackets
2 Mounting bracket
3
M5 × 12 mm hex bolts with washers
Recommended torque : 0.6 N·m to 1.2 N·m
1
Camera ECU box
6 mm to 8 mm (Length protruding inside)
CAUTION
· If you should lose screws that come with the device, use either M5 × 12 mm hex bolts with washers or
screws of a length that protrude inside the ECU box to a depth of 6 mm to 8 mm.
Be sure to follow this precaution as using longer bolts may result in damage to the threads, prevent the
mounting bracket from getting tight enough and/or cause the screws to come out during operation of
the vehicle.
· The recommended torque for
3
M5 × 12 mm hex bolts with washers is 0.6 N·m to 1.2 N·m.
Be careful not to damage the threads by over-tightening the bolts.
WIRING AND CONNECTIONS
Wiring Precautions
Be sure to read the Safety Precautions prior to wiring and follow
them throughout.
WARNING
Failure to do so may result in shock and/or
injury due to a short circuit.
It may also lead to damage to the system
components due to a short circuit.
Disconnect the negative terminal of the battery before connecting the
cables.
Main
power supply
GND
Accesorry
power supply
CAM 1
カメラ 1
CAM-2
カメラ-2
CAM-3
カメラ-3
CAM-4
カメラ-4
40P connector
Electrical system
connector (12P connector)
16P connector
32P connector
Black
Black
Black
Black
Yellow
Yellow
Yellow
Black
Red
White
Black
White
Blue/White
Green/White
Purple/White
Brown/Red
Camera input terminal.
Connect if using CAM 1 / カメラ 1.
Camera input terminal.
Connect if using CAM-2 / カメラ-2.
Camera input terminal.
Connect if using CAM-3 / カメラ-3.
Camera input terminal.
Connect if using CAM-4 / カメラ-4.
Image OUT terminal (RCA connector).
Connect to monitor.
There are 2 identical connectors, and either can be used.
Backup power (DC +12V/24V)
Connect to the power source that normal supplies power.
Ground (GND)
Connect to a metal part of the vehicle.
ACC power (DC +12V/24V)
Connect to power supply that turnsON/OFF with the ignition key.
Spare signal
For use in situations like the door signal for a bus.
Connect to the power supply that is supplied when the door is open.
Connect to the interface box (sold separately) used during calibration and setup.
Fuse 5A
Fuse 5A
Included:
5
32P connection cable
Included:
4
12P electrical system cable
Included:
6
40P connection cable
1 Camera ECU box
connector panel
L directional indicator signal
Connect to the power supply that is supplied when the left directional indicator is
blinking.
R directional indicator signal
Connect to the power supply that is supplied when the right directional indicator is
blinking.
Reverse signal (DC 10.8V to 28V)
Connect to the power supply that is supplied when the gear shift is in the reverse
position.
Connect to the 16P connector of the
Camera ECU box.
Connect to a screen toggling switch
(RCB-210), which is sold separately.
CAUTION
CAUTION
Fuse
Fuse case
Terminal
on vehicle side
· When replacing a fuse, be sure to use one of the same
capacity.
· Putting in the wrong fuse may cause a fault, so check
the amperage of the fuses before replacing them.
When a fuse blows, follow the procedures below for preventing a short circuit and
replace the blown fuse with one of the same capacity.
Take care that the terminal on the vehicle side
does not touch any other metal part.
1. Disconnect the 12P electrical system cable.
2. Make sure all the wires are connected correctly.
3. After making sure everything is correct, replace the blown fuse with one of the
same capacity.
Camera Connections
For an outline of where to make camera connections, see the column for camera connection points for your system.
For details, such as on vehicle type or the cameras to connect for a given system specification, see the PDF manual in the
PC setup application. Please take care as a mistake in the camera connection points will prevent displaying the images cor-
rectly.
Camera Connection
Points by System
Camera System
2 Camera
3 Camera
4 Camera
2+2 Camera
Vehicle example
Truck (Right
steering wheel)
Truck (Left
steering wheel)
Shovel
Bus
Truck (Right
steering wheel)
Truck (Left
steering wheel)
Camera IN
Terminal
Harness Tag
CAM 1
カメラ
1
Not connected
Not connected
Not connected
Front
OP:
Left-rear corner
OP:
Right-rear corner
CAM-2
カメラ
-2
Not connected
Right
Right
Right
OP:
Right-rear corner
Right
CAM-3
カメラ
-3
Left
Not connected
Left
Left
Left
OP:
Left-rear corner
CAM-4
カメラ
-4
Rear
Rear
Rear
Rear
Rear
Rear
OP: Optional
Camera Connections
2


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Clarion EG-2300E at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Clarion EG-2300E in the language / languages: English as an attachment in your email.

The manual is 0,7 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info