580431
14
Zoom out
Zoom in
Previous page
1/328
Next page
Basic Operations
English
14 DXZ588RUSB
Adjusting Sound Mode
Adjusting the subwoofer output
volume
You can adjust the volume output from the unit’s
subwoofer output terminal.
2-1. Select the “S-W VOL”.
3-1. Press the [UP] or [DN] button to change the
output volume.
The factory default setting is “0”.
(Setting range: +5 to –5)
Setting the Digital Z-Enhancer
This unit are provided with 3 types of sound tone
effects stored in memory. Select the one you
prefer.
The factory default setting is “DZE OFF”.
2-1. Select the “DZE”.
3-1. Press the [UP] or [DN] button to select the
tone effect. Each time you press the [UP] or
[DN] button, the tone effect changes in the
following order:
DZE OFFDZE 1DZE 2
DZE 3
DZE OFF : no sound effect
DZE 1 : Suitable for genuine speakers
DZE 2 : Suitable for separate
speakers
DZE 3 : Suitable for co-axial speakers
3-2. When the “DZE 1”, “DZE 2” or “DZE 3” is
set, press the [ ] button. Then
press the [UP] or [DN] button to change the
DZE level from +3 to –3.
The factory default setting is “0”.
3-3. Press the [ ] button to return to the
previous mode.
Compensation
There is no need to compensate frequency
characteristics if they are flat (no peaks or
valleys) when you have measured the
frequency characteristics with a measuring
device. However, sometimes the frequency
characteristics rise or fall in some places. If this
happens, the frequency characteristics must be
compensated. Create a frequency curve having
characteristics that are opposite to the center
frequency of parts where the characteristics rise
and fall to cancel out these peaks and values,
and make the frequency characteristics as flat
as possible.
Making the frequency characteristics as flat as
possible is called “Compensation”.
Compensation of frequency
characteristics
The figure below shows the relationship
between the center frequency, gain and Q
curve.
To change sound mode
1. Press the [ ] button and select the sound
mode to adjust.
2. Push the [SEEK PANEL] leftward or
rightward to select the “item name”.
S-W VOLDZEBASS
TREBLES RESTORHPF
S-W LPFBALANCEFADER
3. Press the [UP] or [DN] button to select the
“desired setting value”.
In the case of display blinking “ENT”, you
can press the [] button to adjust the
setting value.
BASS” and “TREBLE” can be adjusted
only when “DZE is set to “DZE OFF” (page
14).
After completing settings, press the []
button to return to the previous mode.
Note:
•During sound adjustment mode, if no
operation is performed for more than 10
seconds, this mode can be canceled and
return to the previous mode.
3dB
Q =
F
f
f
Center
Frequency (F)
Frequency
(Hz)
Q curve(Q)
Frequency
curve
Level
(dB)
Gain
01_DXZ588RUSB_EN.book 14 ページ 2007年11月27日 火曜日 午後6時5分
14


Need help? Post your question in this forum.

Forumrules
1

Forum

clarion-dxz588rusb

Reset search

  • How do you turn the power of the DXZ588RUSB on and off Submitted on 22-8-2023 at 13:41

    Reply Report abuse


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Clarion DXZ588RUSB at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Clarion DXZ588RUSB in the language / languages: English as an attachment in your email.

The manual is 21,81 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info