631761
4
Zoom out
Zoom in
Previous page
1/23
Next page
Important notes for siting and installation
Place of installation
Every electronic device generates heat. The rise in temperature, however, lies within a safe range.
Slight colour changes may occur to sensitive furniture surfaces and veneers over the course of time due
to the constant effect of heat. In conjunction with treated furniture surfaces, the unit’s rubber feet can
likewise give rise to changes in colour. Where necessary, place the unit on a suitable pad.
Ventilation
The heat which is generated in this unit is dissipated quite adequately. Never install the receiver in a
cabinet, shelf or rack with inadequate ventilation. Never close off the cooling slots on the unit.
Do not place objects on top of the unit. Maintain a clearance of at least 10 cm above the unit, so that the
heat generated within the unit is conducted away without obstruction.
Humidity, exposure to sunlight, heat
Protect the unit against humidity, drips and splashing.
Do not place the unit close to radiators nor expose it to direct sunlight.
Mains voltage
Operate the receiver only from a 230V / 50 Hz mains voltage.
The unit must not be connected to the mains and switched on until after the connections have been set
up for the antenna and TV set.
Grounding
The parabolic antenna is to be grounded in accordance with regulations. The relevant local and/or
German VDE regulations are to be observed.
Remote control
Place the supplied batteries into the remote control. Ensure correct polarity of the batteries according to
the + and – markings inside the battery compartment!
2. Connections
The following connections are located on the rear panel of the unit:
230V / 50 Hz Connect the mains cable with the mains socket.
AUDIO TV L a. R Audio output, left and right channel for connection to a stereo system.
TV Connect the TV socket to your television set with the Scart cable, which is
included in the scope of delivery.
VCR VCR Scart socket for connection of a video recorder.
SAT IF INPUT Sat IF signal input and output for LNB supply and control signals –
Connect the cable from your satellite system to this socket.
SAT IF OUTPUT IF signal output (Loop-through e.g. to an analogue receiver).
DATA INTERFACE RS 232 interface for serial data transmission for servicing.
0-modem cable (Pin 2 and 3 crossed, Pin 1, 4, 6-9 are not used).
Receiver: PC:
Pin 2 = RXD Pin 2 = RXD
Pin 3 = TXD Pin 3 = TXD
Pin 5 = GND Pin 5 = GND
- 4 -
4


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for CITYCOM CCR 512-S at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of CITYCOM CCR 512-S in the language / languages: English as an attachment in your email.

The manual is 0,86 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of CITYCOM CCR 512-S

CITYCOM CCR 512-S User Manual - German - 23 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info