455913
3
Zoom out
Zoom in
Previous page
1/3
Next page
Applications
The Z5M can be used for any multi-output setup and is ideally suited to controlling a multi-room zoning sound system with up to 5 stereo or
mono zones. Individual zones can be selected as mono if speaker placement is not conducive to stereo imaging. 2 separate stereo inputs can be
selected or blended at will for each zone, opening up the possibility of separate program material for specific zones. Prior to rack-mounting the
unit, it is important to know what the mains supply voltage will be, since the voltage selector is situated on the side panel towards the rear of the
unit.
Connection
All connections are via balanced XLR and operate at line level. Use good quality XLR signal leads to connect the source signals to LINE 1 and
LINE 2 inputs. Each output should be connected to the respective amplifier or active speakers for the particular zone, again using good quality
XLR signal leads. Connect mains using the supplied IEC lead.
Operation
Set amplifier and active speaker volume levels fully down
Set LINE 1 and LINE 2 levels for each zone to “MIN”
Select MONO for any zones that are better suited to mono output.
Press the POWER switch on and play the signals connected to LINE 1 and LINE 2 inputs.
The LINE SIGNAL LEDs should indicate the presence of each input signal.
Gradually increase and then decrease the volume for LINE1 and LINE 2 to each zone in turn to check the output.
Set the volumes and adjust for each source to each zone as required.
Before powering the Z5M down, turn down amplifier and active speaker volumes to avoid loud noises through the speakers.
SPECIFICATIONS
Item
Value
Power supply
115/230Vac 50/60Hz - selectable (IEC)
Inputs
Line 1 L+R, Line 2 L+R, balanced XLRF
Outputs
Zone 1 to 5 L+R, balanced XLRM
Input impedance
40kohms
Output impedance
220ohms
Frequency response
20Hz - 25kHz, +0/-1dB
Signal to noise ratio
>100dB
THD
<0.005%
Dimensions
483 x 175 x 44mm
Weight
2.2kg
TROUBLESHOOTING
No function and Power switch LED is not lit
Ensure mains voltage is correct (check selector) and connected properly
Ensure front panel power switch and mains outlet switch are on
Power is on but no audio output
Check all XLR leads are OK and connected properly
Check that LINE 1 and LINE 2 controls are not all turned fully down
Check that inputs and outputs are connected the correct way around
Distorted output
Reduce LINE 1 and LINE 2 level controls, increasing amp level to compensate
Reduce level of source signal(s) connected to LINE 1 and LINE 2 inputs
Ensure correct line level is selected on amplifier/active speaker inputs
Output is very low level
Ensure input source is line level (0.775Vrms)
Increase LINE 1 and/or LINE 2 level controls,
Increase signal source level
Note: for further troubleshooting, refer equipment to qualified service personnel for testing
© Citronic 2011
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Citronic Z5M at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Citronic Z5M in the language / languages: English as an attachment in your email.

The manual is 0,37 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info