Manual Citizen CL-S703 (page 65 of 80) (English)

556044

Zoom out

Zoom in

1/80

Troubleshooting

Indication

The printer is not

printing neatly.

The printing position

changes.

The ribbon is wrinkled

The ribbon slips

(ribbon dirt is

produced.)

The ribbon does not

wind.

Check

4) Is the thermal printhead

dirty?

Is a label stuck to the head.

5) Is the recommended

ribbon or a ribbon of the

same type used?

6) Is the thermal printhead in

the correct position for the

media that is used?

7) Is the printer’s head

pressure balance correct

for the width of the media

that is used?

1) Are the media and the

ribbon correctly set?

2) Is the platen dirty?

Is it deformed?

3) Are the data contents and

the command signals from

the host appropriate?

4) Are the menu values set

appropriately?

5) Are the sensitivities of the

media sensors appropriate

for the media that is used?

1) Is the ribbon tension

suitable for the ribbon that

is used?

2) Is the ribbon used correctly

balanced to the right and

left?

3) Is the printing density too

high?

4) Are the media and ribbon

the recommended

products or equivalent

products?

1) Is the ribbon tension

suitable for the ribbon that

is used?

1) Is the ribbon set in the

correct course?

2) Is the ribbon winding

direction reversed?

Corrective action

4) If it is dirty, remove the dirt with the

attached head cleaner.

If a label is stuck to the head, remove

it.

Note: Do not use a metal object to

remove a label stuck to the inside of

the printer. (This may damage the

thermal printhead .) If adhesive label

material is stuck to the print head,

remove it with a soft cloth soaked in

ethyl alcohol.

5) Use the recommended ribbon or a

ribbon of the same type.

6) Adjust the offset of the thermal

printhead with the media thickness

adjustment dial.

7) Adjust the thermal printhead pressure

with the media width adjustment dial.

1) Correctly set the media and the ribbon.

2) If it is dirty, clean it with ethyl alcohol.

If it is deformed, replace it.

Note: Consult with the dealer that

supplied the printer concerning the

replacement.

3) If an error message is displayed, check

the content of the software and the

communication status set by the host

computer.

4) Set the correct menu values using the

operating panel or the host computer.

5) Set the media sensitivity to appropriate

values.

If this does not solve the problem,

change the “Sensor level” that is set in

the “System setup.”

1) Adjust the tension with the adjust-

screw.

2) Adjust the left - right balance with the

media width adjustment knob.

3) Set the appropriate printing density

using the menu or control software.

4) Use the recommended products or

equivalent products. If this does not

correct the problem, contact a service

representative.

1) Adjust the tension with the adjust-

screw.

1) Set the ribbon in the correct course.

2) Set the correct winding direction.

Media Thickness

Adjustment (p.57)

Media Width

Adjustment (p.58)

Installing the Media

(p.25, P27)

Setting method (p.32)

Cleaning (p.62)

LED Functions (p.22)

Menu Setting Table

(p.43)

Adjusting the Ribbon

(p.59)

Setting the Ribbon

(p.32)

Adjusting the Ribbon

(p.59)

Setting the Ribbon

(p.32)

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Citizen CL-S703 in the language / languages: English as an attachment in your email.

The manual is 2,21 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Citizen CL-S703 Manual

Product: