556035
36
Zoom out
Zoom in
Previous page
1/64
Next page
36
Chapter 2 Printer Operation
Top Menu Sub Menu Default Menu Remarks
Cutter Action Backfeed Backfeed
Through
Sets the cutter action.
With the optional AutoCongure On,
printing is executed only when the cutter
is installed or only when Cut is selected by
Function Select.
Backfeed is always set after cutting.
Through is set at the rear end of sheets 1 to
n-1 when the number of copies = n, and the
rear end of the nal page of single sheet and
the copy is backfeed.
Peel Wait Delay* 0.1 sec 0.1 to 2.0 sec Sets the Peel Wait Delay.
Displays only machines with a peeler
installed.
Paper Position 0.00 inch
0.0 mm
Peel/Cut/Tear O
0.00 to 2.00 inch
0.0 to 50.8 mm
Peel/Cut/Tear On
-1.00 to 1.00 inch
-25.4 to 25.4 mm
Adjusts the stop position. It is based on the
inch/millimeter setting. There are initial
values of the stop position for each device
set above, and later, relative values are set.
Menu Key Action Enters Menu Enters Menu
Repeat Label Set
Repeat Last One
Sets the menu key action.
Enters Menu:
Enters the menu setup mode.
Repeat Label Set:
Repeats the number of copies.
Repeat Last One:
Last one is issued only for the nal page.
In the case of a count, afterwards, only
last one is issued.
Note: Hold down the MENU key for at least
4 seconds in order to enter the Menu Setup
Mode when setting the “Repeat Label Set or
“Repeat Last One” menus.
Interfaces RS-232C Baud 9600 115200
57600
38400
19200
9600
4800
2400
Setting the baud rate of the serial interface.
All settings related to the interface are
enabled after the power is reconnected.
RS-232C Parity None None
Odd
Even
Setting the communication parity for the
serial interface.
RS-232C Length 8 bits 8 bits
7 bits
Setting the character length for the serial
interface.
RS-232C Stop bit
[RS-232C Stopbit]
1 bit 1 bit
2 bits
Setting the stop bit for the serial interface.
RS-232C X-ON Yes Yes
No
Selectively setting the X-ON ow control of
the serial interface.
IEEE1284 On On
O
Setting both direction of the Centro
Interface.
* Only when cutter is mounted.
Mode Settings
[Datamax® Emulation]
36


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Citizen CL-S400DT at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Citizen CL-S400DT in the language / languages: English, French as an attachment in your email.

The manual is 4,55 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info