Manual Cisco WRT120N (page 14 of 55) (English)

475373

Zoom out

Zoom in

1/55

Chapter 3

Advanced Configuration

Wireless-N Home Router

Route Entries To set up a static route between the Router

and another network, select a number from the drop-

down list. Click Delete This Entry to delete a static route.

Enter Route Name Enter a name for the Route here,

using a maximum of 25 alphanumeric characters.

Destination LAN IP The Destination LAN IP is the address

of the remote network or host to which you want to assign

a static route.

Subnet Mask The Subnet Mask determines which

portion of a Destination LAN IP address is the network

portion, and which portion is the host portion.

Default Gateway This is the IP address of the gateway

device that allows for contact between the Router and the

remote network or host.

Interface This interface tells you whether the Destination

IP Address is on the LAN & Wireless (Ethernet and wireless

networks) or the WAN (Internet).

Click Show Routing Table to view the static routes you

have already set up.

Advanced Routing > Routing Table

Routing Table

For each route, the Destination LAN IP address, Subnet

Mask, Gateway, and Interface are displayed. To update

the information, click Refresh. To exit this screen and

return to the Advanced Routing screen, click Close.

Click Save Settings to apply your changes, or click Cancel

Changes to clear your changes.

Wireless > Basic Wireless Settings

The basic settings for wireless networking are set on this

screen.

There are two ways to configure the Router’s wireless

network(s), manual and Wi-Fi Protected Setup.

Wi-Fi Protected Setup is a feature that makes it easy to set

up your wireless network. If you have client devices, such

as wireless adapters, that support Wi-Fi Protected Setup,

then you can use Wi-Fi Protected Setup.

Configuration View To manually configure your wireless

network, select Manual. Proceed to Basic Wireless

Settings (Manual), page 10. To use Wi-Fi Protected

Setup, select Wi-Fi Protected Setup. Proceed to Wi-Fi

Protected Setup, page 11.

Basic Wireless Settings (Manual)

Wireless > Basic Wireless Settings (Manual Setup)

Network Mode From this drop-down menu, you can

select the wireless standards running on your network. If

you have Wireless-N, Wireless-G, and Wireless-B devices in

your network, keep the default, Mixed. If you have only

Wireless-G and Wireless-B devices in your network, select

BG-Mixed. If you have only Wireless-N devices, select

Wireless-N Only. If you have only Wireless-G devices,

select Wireless-G Only. If you have only Wireless-B

devices, select Wireless-B Only. If you do not have any

wireless devices in your network, select Disabled.

Network Name (SSID) The SSID is the network name

shared among all points in a wireless network. The

SSID must be identical for all devices in the wireless

network. It is case-sensitive and must not exceed

32 characters (use any of the characters on the keyboard).

Make sure this setting is the same for all points in your

wireless network. For added security, you should change

the default SSID (linksys) to a unique name.

Channel Width For best performance in a Wireless-N

network, select 40MHz only. For Wireless-G and Wireless-B

networking only, keep the default, 20MHz only. If you

are not sure which option to use, select Auto (20MHz or

40MHz).

NOTE: If you select 40MHz only for the Channel

Width setting, then Wireless-N can use two

channels: a primary one (Wide Channel) and

a secondary one (Standard Channel). This will

enhance Wireless-N performance.

Wide Channel If 40MHz only is the Channel Width

setting, then this setting will be available for your primary

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Cisco WRT120N in the language / languages: English as an attachment in your email.

The manual is 3,4 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Cisco WRT120N Manual

Product: