300769
150
Zoom out
Zoom in
Previous page
1/165
Next page
5-45
Linksys IP Phone Administrator Guide
Firmware Version 5.1
Chapter 5 Linksys IP Phone Field Reference
Ext Tab
A codec resource is considered allocated if it has been included in the SDP codec list of an active call,
even though it eventually might not be chosen for the connection. If the G.729a codec is enabled and
included in the codec list, that resource is tied up until the end of the call whether or not the call actually
uses G.729a. If the G729a resource is already allocated (and since only one G.729a resource is allowed
per SPA), no other low-bit-rate codec can be allocated for subsequent calls. The only choices are G711a
and G711u.
Since two G.723.1/G.726 resources are available per SPA, you should disable the use of G.729a to
guarantee support for two simultaneous G.723/G.726 codecs.
FAX CNG Detect Enable Defaults to yes.
FAX Passthru Codec Codec to use for FAX passthru (G711u or G711a).
Defaults to G711u.
FAX Codec Symmetric Force unit to use symmetric codec druing FAX passthru.
Defaults to yes.
FAX Passthru Method Choose None, NSE, or ReINVITE.
Defaults to NSE.
FAX Process NSE Defaults to yes.
FAX Disable ECAN Set to yes to automatically disable Echo Canceller when FAX tone is detected.
Defaults to no.
DTMF Tx Method Select the method to transmit DTMF signals to the far end: InBand, AVT, INFO, Auto,
InBand+INFO, or AVT+INFO. InBand sends DTMF using the audio path. AVT sends
DTMF as AVT events. INFO uses the SIP INFO method. Auto uses InBand or AVT based
on the outcome of codec negotiation.
Defaults to Auto.
Hook Flash Tx Method Select the method to signal Hook Flash events:
None: do not signal hook flash events
AVT: use RFC2833 AVT (event=16)
INFO: use SIP INFO method with the signal line “signal = hf” in the message body. The
MIME type for this message body is taken from the <Hook Flash MIME Type> parame
-
ter.
Defaults to None.
Symmetric RTP Enable symmetric RTP operation. If enabled, the SPA sends RTP packets to the source
address of the last received valid inbound RTP packet. If disabled, the SPA sends RTP to
the destination as indicated in the inbound SDP.
Defaults to yes.
Release Unused Codec This feature allows the release of codecs not used after codec negotiation on the first call,
so that other codecs can be used for the second line. To use this feature, select yes.
Otherwise, select no.
Defaults to yes.
Field Description
150


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cisco spa921 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cisco spa921 in the language / languages: English as an attachment in your email.

The manual is 3,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cisco spa921

Cisco spa921 User Manual - Dutch - 19 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info