300769
130
Zoom out
Zoom in
Previous page
1/165
Next page
5-25
Linksys IP Phone Administrator Guide
Firmware Version 5.1
Chapter 5 Linksys IP Phone Field Reference
Regional Tab
Vertical Service Announcement Codes
Note None of the following parameters apply to the SPA901.
Service Annc (Annoucement) Base Number: Defaults to blank.
Service Annc (Announcement) Extension Codes: Defaults to blank.
Outbound Call Codec Selection Codes
These codes automatically appended to the dial-plan. So no need to include them in dial-plan (although
no harm to do so either).
Feature Dial Services Codes These codes tell the Linksys IP phone what to do when the user is listening to the first or
second dial tone.
One or more *code can be configured into this parameter, such as *72, or
*72|*74|*67|*82, etc. Max total length is 79 chars. This parameter applies when the user
has a dial tone (first or second dial tone). Enter *code (and the following target number
according to current dial plan) entered at the dial tone triggers the Linksys IP phone to
call the target number prepended by the *code. For example, after user dials *72, the
Linksys IP phone plays a prompt tone awaiting the user to enter a valid target number.
When a complete number is entered, the Linksys IP phone sends a INVITE to
*72<target_number> as in a normal call. This feature allows the proxy to process features
like call forward (*72) or BLock Caller ID (*67).
The *codes should not conflict with any of the other vertical service codes internally
processed by the Linksys IP phone. You can empty the corresponding *code that you do
not want to Linksys IP phone to process.
You can add a parameter to each *code in Features Dial Services Codes to indicate what
tone to play after the *code is entered, such as *72‘c‘|*67‘p‘. Below are a list of allowed
tone parameters (note the use of back quotes surrounding the parameter w/o spaces)
‘c‘ = <Cfwd Dial Tone>
‘d‘ = <Dial Tone>
‘m‘ = <MWI Dial Tone>
‘o‘ = <Outside Dial Tone>
‘p‘ = <Prompt Dial Tone>
‘s‘ = <Second Dial Tone>
‘x‘ = No tones are place, x is any digit not used above
If no tone parameter is specified, the Linksys IP phone plays Prompt tone by default.
If the *code is not to be followed by a phone number, such as *73 to cancel call
forwarding, do not include it in this parameter. In that case, simple add that *code in the
dial plan and the Linksys IP phone send INVITE *73@..... as usual when user dials *73.
Field Description
130


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cisco spa921 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cisco spa921 in the language / languages: English as an attachment in your email.

The manual is 3,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Cisco spa921

Cisco spa921 User Manual - Dutch - 19 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info