97426
48
Zoom out
Zoom in
Previous page
1/71
Next page
Appendix A
Troubleshooting
44
Media Hub
Appendix A:
Troubleshooting
The power LED of the Media Hub continuously ashes
blue or red.
Follow these instructions:
To shut down the Media Hub, press and hold the power 1.
button until the power LED starts flashing.
If this step does not shut down the Media Hub, then
proceed to step 2.
Disconnect the power adapter from the Power port of 2.
the Media Hub.
Disconnect the Ethernet network cable from the 3.
Ethernet port of the Media Hub.
Wait five seconds.4.
Re-connect the Ethernet network cable to the Ethernet 5.
port of the Media Hub.
Re-connect the power adapter to the Power port of 6.
the Media Hub.
You cannot access the Media Browser of the Media Hub.
Follow the instructions until you gain access to the Media
Browser:
Make sure your computer is connected to the local 1.
network. Check the wireless or wired connection.
Make sure the Media Hub is connected to the router. 2.
Check the cable connection at both ends.
Double-click the desktop icon for the Media Hub (it 3.
was created during the Setup Wizard).
In the4. Address field of your web browser, make sure
you entered the Friendly Name correctly.
The Friendly Name is the name you created during the
Setup Wizard. If you did not create a Friendly Name,
use the default name; enter http://mediahub
NOTE: To access the Media Browser from a Mac,
use one of the following:
http://<Friendly_Name>.local
<Friendly_Name>.local
http://<IP_address_of_Media_Hub>
You have congured the Media Hub, but you do not see
it displayed in Windows Explorer.
Change the Workgroup of the Media Hub to match the
Workgroup of your computer. Follow these instructions:
Access the web-based utility of the Media Hub. (Refer 1.
to Chapter 7: Advanced Configuration, page 35.)
On the 2. Media Browser screen, click Configuration.
Click 3. Configure System.
For the Media Hub Name and Workgroup settings, click 4.
Change, and then follow the on-screen instructions.
NOTE: If you do not see a drive letter for the
Media Hub, refer to Drive Letter Not Found,
page 7.
You cannot access the Media Browser, or the Media Hub
does not respond to commands.
Before You Begin
The Media Hub must boot up with at least one hard disk
installed. If Disk 1 has been removed and replaced with a
new hard disk, then the recovery procedure can be used
to re-install the Media Hub.
WARNING: Before you install the new hard disk,
back up its existing data because all data on the
new hard disk will be erased.
Instructions for the Recovery Procedure
To shut down the Media Hub, press and hold the power 1.
button until the power LED starts flashing.
If this step does not shut down the Media Hub, then
proceed to step 2.
Disconnect the power adapter from the Power port of 2.
the Media Hub.
While you press and hold down the 3. Reset button,
re-connect the power adapter to the Power port of the
Media Hub.
Continue to hold down the 4. Reset button for
ten seconds. Then release.
The Media Hub will undergo its recovery procedure.5.
WARNING: Do not reboot or power off the
Media Hub during the recovery procedure.
The recovery procedure will reset the firmware to its
factory version, so you may need to do a firmware upgrade
when the recovery procedure is complete.
48


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cisco NMH305 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cisco NMH305 in the language / languages: English as an attachment in your email.

The manual is 8,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info