97426
44
Zoom out
Zoom in
Previous page
1/71
Next page
Chapter 7
Advanced Configuration
40
Media Hub
When prompted to confirm the new disk configuration,
click Yes to continue, or click No to cancel.
WARNING: For the Increase Space: Linear 2
mode, if one of the two hard disks fails, then all
data will be lost.
Before you click this option, review the following:
The Media Hub is designed to maintain existing
data during disk configuration; however, Linksys
recommends that you back up its data to your
computer or an external hard disk before you
continue.
When you set the Media Hub to the Increase Space:
Linear 2 mode, the Media Hub will be unavailable for
approximately 15 minutes and then automatically
reboot.
Do not manually reboot or power off the Media Hub
during this time.
After reboot, available disk space will increase to the
total size of both hard disks.
? Increase Protection (available only for two installed
disks) To help enhance data reliability, click this option,
also known as RAID 1 mode. Disk 2 holds a copy of the
data on Disk 1. For more information, click the ? icon.
When prompted to confirm the new disk configuration,
click Yes to continue, or click No to cancel.
NOTE: For the Increase Protection: RAID 1 mode,
Disk 2 must be equal to or larger in size than
Disk 1. If one disk is smaller, only the smaller size
will be used for this mode.
Before you click this option, review the following:
WARNING: Existing data on the Media Hub will
be lost; Linksys strongly recommends that you
back up its data to your computer or an external
hard disk before you continue.
When you set the Media Hub to the Increase Protection:
RAID 1 mode, the Media Hub will be unavailable for
approximately 15 minutes and then automatically
reboot.
After reboot, the Media Hub will synchronize the data
on the two disks.
Depending on disk size, disk synchronization may take
from several minutes to several hours. Synchronization
progress can be viewed from the Disk screen. Rebooting
or removing power from the Media Hub during this
time is not recommended.
NOTE: You may use the Media Hub during disk
synchronization; however, it will perform at
slower speeds.
After configuration, available disk space will be the
size of Disk 1, and your data will be more protected
from damage or loss if a disk fails.
? Revert to single disk mode To reset the Media Hub
to its factory default settings, click this option. All data
on your hard disk will be deleted, and all configuration
settings will be reset to their factory defaults. For more
information, click the ? icon.
Before you click this option, review the following:
If the Media Hub has two disks, Linksys recommends
that you remove one of the disks before continuing.
Existing data on the Media Hub will be lost; Linksys
strongly recommends that you back up its data to
your computer or an external hard disk before you
continue.
Depending on disk size, configuration may take from
several minutes to several hours. Do not manually
reboot or power off the Media Hub during this time.
After configuration, available disk space will be the
size of your single hard disk.
Rebuild This option appears only if two disks are installed
and one disk is detected as new. To rebuild the Increase
Protection: RAID 1 configuration, click this option.
Before you click this option, review the following:
Replace the defective disk (refer to Replace a Hard
Disk, page 3).
Depending on disk size, disk configuration may take
from several minutes to several hours. Do not manually
reboot or power off the Media Hub during this time.
Rebuild progress can be viewed from the Disk screen.
NOTE: You may use the Media Hub during
configuration; however, it may will perform at
slower speeds.
Backup
The Setup Wizard automatically installs a backup tool on
your computer to run backup jobs (unless you choose not
to install it); refer to NTI Shadow, page 31. If you have
installed the backup tool, then you can use the backup
feature of the Media Hub.
44


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Cisco NMH305 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Cisco NMH305 in the language / languages: English as an attachment in your email.

The manual is 8,11 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info