Manual Cisco EPC2202 (page 25 of 38) (English)

604986

Zoom out

Zoom in

1/38

4028518 Rev B 25

Installing USB Drivers

Your IP cable modem features multiple networking interfaces that allow you to

connect consumer electronic devices to your home network. USB 1.1 is one of the

technologies that enables Microsoft Windows-based PCs to connect to the home

network.

Important: Due to the inherent speed limitations of the technology, USB 1.1 is not

the optimal interface for high-speed networking. The USB 1.1 port should only be

used when there is no other interface available on your PC for connecting to the

network.

This section contains instructions for installing USB drivers if your PC is equipped

with a USB interface and a Microsoft Windows 2000, XP, or Vista operating system.

The USB driver installation procedures are different for each operating system.

Follow the appropriate instructions in this section for your operating system.

Note: If you are not using the USB interface, skip this section.

Installing USB Drivers on Windows 2000 Systems

1 Insert the USB Cable Modem Driver Installation Disk into the CD-ROM drive

of your PC.

2 Make sure the power is connected to your cable modem and that the POWER

LED status indicator on the front panel of the cable modem illuminates solid.

3 Connect the USB cable to your computer's USB port. Then, connect the other end

of the USB cable to the USB port on the cable modem.

4 Click Next in the Found New Hardware Wizard window.

5 Select Search for a suitable driver for my device (recommended) in the Found

New Hardware Wizard window, and then click Next.

6 Select CD-ROM drives in the Found New Hardware Wizard window, and then

click Next.

7 Click Next in the Found New Hardware Wizard window. The system searches

for the driver file for your hardware device.

8 After the system finds the USB driver, the Digital Signature Not Found window

opens and displays a confirmation message to continue the installation.

9 Click Yes to continue the installation. The Found New Hardware Wizard

window reopens with a message that the installation is complete.

10 Click Finish to close the Found New Hardware Wizard window. The USB

drivers are installed on your PC, and your USB devices are ready for use.

11 Try to access the Internet. If you cannot access the Internet, go to Having

Difficulty? (on page 30). If you still cannot access the Internet, contact your

service provider for further assistance.

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Cisco EPC2202 in the language / languages: English as an attachment in your email.

The manual is 1,68 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Cisco EPC2202 Manual

Product: