588917
7
Zoom out
Zoom in
Previous page
1/16
Next page
46 47
If the 12-hour display is selected later, the CM 628 con-
verts the time automatically.
Setting the year
Set with right button, save and
continue with left button.
Year range = 2000 - 2099
Setting the day/month
Set with right button, save and
continue with left button.
Day range = 1 - 31
Month range = 1 - 12
Now the current date can be set
(with 24-hour display in the day/month format, with 12-
hour display in the month/day format).
The following adjustment (Chap. 4.5) appears only if the
cadence has been switched on (see Chap. 4.1).
4.5 Initialization of the cadence transmitter
Press the right button until the
following display appears:
By pressing the left button for 3
sec., this display now appears:
Initialization of the cadence transmitter
The initialisation display for the cadence appears in the
display (= Cadence).
If no cadence transmitter has been initialised for the actual
bike, start the initialisation now (see below).
If a cadence transmitter has already been initialised,
change into the operating mode through short pressing of
the left button.
Before the transmitter search, allow the magnet to pass in
front of the cadence transmitter once (1 pedal rotation).
This will start the Transmitter and emit a signal for approx.
3 minutes.
Before the transmitter search, allow the magnet to pass in
front of the speed transmitter once (1 wheel rotation).
This will start the Transmitter and emit a signal for approx.
3 minutes.
Start the transmitter search in the CM 628 by pressing
both buttons for a short time.
A percentage value runs up in the
display during the initialisation (see
Fig.)
After a successful initialisation, the
CM 628 changes automatically into the normal operating
mode and the indication SPD/AV appears in the display.
In the case of an unsuccessful
initialisation (see Fig.), the
transmitter search can be started
again by repeated short pressing of
both buttons.
The initialisation can be interrupted after a fault by short
pressing of the left button, the CM 628 then switches to
the normal operating mode.
Pay attention during the initialisation that no second speed
transmitter is located nearby (currently active).
A transmitter already initialised to Bike 1 cannot also be
initialised for Bike 2 (or vice-versa).
4.4 Setting the time and date
Press the right button shortly until
the following display appears:
By pressing the left button for 3
sec., this display now appears:
Time-of-day display: 24-hour
or 12-hour (AM/ PM) indication.
Adjust with right button (save and
continue with left button).
If the 12-hour indication is selected,
a "P" appears before the time in
case of PM time.
Setting the time
Adjust with right and left button
(save and continue with left button).
Time range = 00:00 - 23:59
Here the current time is set in the
24-hour format. (If the 12-hour
display had been selected,
00:00 - 12:59 AM/PM can also be entered; a "P" appears
before the time in case of PM time)
02 CM 628 englisch 34-65 19.05.2005 10:23 Uhr Seite 14
7


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ciclo CM 628 Master at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ciclo CM 628 Master in the language / languages: English as an attachment in your email.

The manual is 0,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ciclo CM 628 Master

Ciclo CM 628 Master User Manual - German - 17 pages

Ciclo CM 628 Master User Manual - Dutch - 17 pages

Ciclo CM 628 Master User Manual - French - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info