588917
3
Zoom out
Zoom in
Previous page
1/16
Next page
38 39
2.1 Installing the handlebar bracket
The handlebar bracket can be attached to the handlebars
or to the stem. To use on the stem, slide off the upper part
of the handlebar bracket from the lower section by
pressing the snap-closure
mechanism (e.g. with a pin).
Now rotate upper part through
90° and reconnect to the lower
part, until the snap-closure
mechanism engages audibly
and visibly.
Remove the protective foil on
the underside of the handlebar
bracket and place the handlebar
bracket at the required location
on the handlebars (or on the
stem) and press slightly. Fasten
with the cable tie.
Slide the CM 628 onto the
bracket in the direction of the
arrow until it engages audibly and
visibly (release button must be at
the initial position). In order to
remove it again, press down the release button behind the
CM 628 and remove the CM 628 with light pressure.
2.2 Installing the speed transmitter
Attach speed transmitter to the
fork or to the rear construction
with the aid of the attached O-
ring (marked side of the trans-
mitter must point to the spokes).
Suspend the O-ring on one side
of the transmitter, wrap it around
the fork and likewise suspend on
the opposite side.
Mount the magnets on a spoke directly opposite the
transmitter, so that the magnet points exactly to the marker
on the transmitter. Do not over tighten the fixing screw on
1. GENERAL INFORMATION
Warning: whoever carries out sport should have a general
medical check up on his/her general state of health -
especially beginners, persons older than 35 years of age
and anyone who has suffered from illnesses or injuries in
the past. It is recommended that a doctor be consulted in
any case in the presence of risk factors, such as smoking,
high blood pressure, high cholesterol values, diabetes, lack
of exercise and excess weight.
Pacemaker wearers should consult their doctor
before using any heart rate measurement device!
Measurement of the heart rate is only possible if the trans-
mitter belt is fitted correctly (see Chap. 2.4) and the
CM 628 is within the transmitter’s reception range
(approx. 10 m).
The CM 628 has been set to receive the signals from the
chest belt. It is supplied ready to use, but may require user
initialisation under certain circumstances (see Chap. 4.6 –
Initializing the receiver for heart rate monitoring).
The heart rate can be measured even when the CM 628 is
not mounted on the bike. In this case start the heart rate
transmitter search by short pressing both buttons when in
heart rate mode ('H' in lower display).
If a appears in the top left of display, the indicated
values apply to Bike 1. In order to display the values for
Bike 2, press both buttons simultaneously for a brief period
(the changeover is only possible if the speed = 0) and a
will appear in the top left of display. To switch back to
values for Bike 1 press both buttons simultaneous again
briefly, and the display will show .
2. OPERATIONAL STARTUP
The CM 628 is set in the power-saving mode. By pressing
any button, it switches to the normal operating mode.
If no characters or unintelligible characters appear in the
display, press the AC button on the reverse side of the
CM 628 (repeat if necessary) with the aid of a ballpoint
pen (or similar).
Caution: Longer pressing of the AC button (3 sec.) causes
a total reset, i.e. the initialisation already carried out at the
works is also deleted with that, and so the speed, as well
as the cadence- and heart rate transmitter, must be initia-
lised again (see Chap. 4.3, 4.5 and 4.6).
02 CM 628 englisch 34-65 19.05.2005 10:23 Uhr Seite 6
3


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Ciclo CM 628 Master at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Ciclo CM 628 Master in the language / languages: English as an attachment in your email.

The manual is 0,31 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Ciclo CM 628 Master

Ciclo CM 628 Master User Manual - German - 17 pages

Ciclo CM 628 Master User Manual - Dutch - 17 pages

Ciclo CM 628 Master User Manual - French - 16 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info