491465
26
Zoom out
Zoom in
Previous page
1/60
Next page
Park your vehicle outside of the garage and turn the ignition switch to the ON/RUN
position.
Place the hand-held transmitter 1 to 3 in (3 to 8 cm) from the HomeLink
®
buttons
while keeping the indicator light in view.
Simultaneously, press and hold both the chosen HomeLink
®
button and the
hand-held transmitter button until the HomeLink
®
indicator flash rate changes
from a slow to a rapidly blinking light, then release both the HomeLink
®
and the
hand-held transmitter buttons. This may take up to 30 seconds, or longer in rare
cases.
Press and hold the just-trained HomeLink
®
button; if the indicator light stays on
constantly, programming is complete and the garage door should open.
WARNING!
Your motorized door or gate will open and close while you are training the
universal transceiver. Do not train the transceiver if people or pets are in the
path of the door or gate. Only use this transceiver with a garage door opener
that has a “stop and reverse” feature as required by Federal safety standards.
This includes most garage door opener models manufactured after 1982. Do not
use a garage door opener without these safety features. Call toll-free
1–800–355–3515 or, on the Internet, at www.HomeLink.com for safety
information or assistance.
Vehicle exhaust contains Carbon Monoxide (CO), a dangerous gas. Do not run
your vehicle in the garage while training the transceiver. Exhaust gas can cause
serious injury or death.
NOTE: If you are having difficulty training your HomeLink
®
and your garage door
opener was manufactured after 1995, you may have a rolling code. Follow the steps
below for Programming A Rolling Code System.
Programming A Rolling Code System
At the garage door opener motor (in the garage), locate the “learn or “training”
button. This can usually be found where the hanging antenna wire is attached to
the garage door opener motor (it is NOT the button normally used to open and
close the door).
Firmly press and release the “learn” or “training” button. The name and color of
the button may vary by manufacturer. Within 30 seconds, return to the vehicle and
press the programmed HomeLink
®
button twice (holding the button for two
seconds each time). If the device is plugged in and activates, programming is
complete.
If the device does not activate, press the button a third time (for two seconds) to
complete the training.
ELECTRONICS
24
26


Need help? Post your question in this forum.

Forumrules


Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

For example, Anti-Semitic content, racist content, or material that could result in a violent physical act.

For example, a credit card number, a personal identification number, or an unlisted home address. Note that email addresses and full names are not considered private information.

Forumrules

To achieve meaningful questions, we apply the following rules:

Register

Register getting emails for Chrysler PT Cruiser 2010 at:


You will receive an email to register for one or both of the options.


Get your user manual by e-mail

Enter your email address to receive the manual of Chrysler PT Cruiser 2010 in the language / languages: English as an attachment in your email.

The manual is 6,49 mb in size.

 

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

Others manual(s) of Chrysler PT Cruiser 2010

Chrysler PT Cruiser 2010 User Manual - English - 368 pages


The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.



Info