Manual Christopeit XL 2 (page 15 of 44) (English, German, Dutch, French)

585792

Zoom out

Zoom in

1/44

English

Assembly Instructions

Remove all the separate parts from the packaging, lay them on the

ﬂoor and check roughly that all are there on the base of the assembly

steps. Please note that a number of parts have been connected directly

to the main frame and preassembled. In addition, there are several

other individual parts that have been attached to separate units. This

will make it easier and quicker for you to assemble the equipment.

Step 1:

Attach the stabilizer (2+3) at main frame (1).

1. Attach the front foot (2) with the preassembled transport rollers (23) to

the main frame (1). Do this with the two screws M8x55 (13), washers 8//25

(14) and cap nuts (15).

2. Attach the rear foot (3) with height adjustable foot caps (25) to the main

frame (1). Do this with the two screws M8x55 (13), washers 8//25 (14) and

cap nuts (15).

After assembly has been completed, you can compensate for minor

irregularities in the ﬂoor by turning the wheel at rear end cap (25).

The equipment should be set up that the equipment does not move of its

own accord during a training session.

Step 2:

Attach the saddle (8) and saddle support tube (6).

1. Push the saddle (8) with saddle bracket into the saddle slide (7) and

tight it up in desired position.

2. Place the saddle slide (7) into the holder of saddle post (6), set it at the

desired position and screw it onto the saddle support (6) by using quick

release knob (11).

3. Push the saddle support tube (6) into the matching locator in the main

frame (1), set it at the desired position and lock it by inserting the bolt with

the L-quick release (22) in place and doing it up tight.

(Note: To screw in the L-quick release (22), the threaded hole in the main

frame (1) and one of the holes in the saddle support (6) must be aligned.

Furthermore, ensure that the saddle support (6) is not pulled out of the main

frame beyond the marked maximum adjustment position. The setting of

the saddle support can be adjusted as desired later.) For this, the L-quick

release (22) must be loosened by only a few revolutions (do not unscrew

completely), the top cap of the lock must be pulled away and the saddle

adjusted. To set the new position, release the top cap and move the saddle

support upwards and downwards until the rapid-action lock engages. Then

secure the new setting by tightening the L-quick release.)

Step 3:

Attach the handlebar (5) and handlebar support (4).

1. Place the handlebar (5) against the handlebar support (4) and adjust so

that the hole patterns in the handlebar and the handlebar support are alig-

ned. Also the computer holder (28) place to the upper holes of connection

point.

Put one spring washer (16) on each screw (12). Push the screws (12)

through the holes in the support, screw into the threaded holes of the sup-

port (4) and tighten ﬁrmly.

2. Place the lower handlebar cover (10B) at handlebar support (4).

Push the handlebar support (4) into the matching locator in the main frame

(1), set it at the desired position and lock it by inserting the bolt with the

L-quick release (22) in place and doing it up tight.

3. Place the upper handlebar cover (10A) on top of handlebar support (4)

and screw together with lower handlebar cover (10A) by using screws (18).

Report abuse

Libble takes abuse of its services very seriously. We're committed to dealing with such abuse according to the laws in your country of residence. When you submit a report, we'll investigate it and take the appropriate action. We'll get back to you only if we require additional details or have more information to share.

Product:

Forumrules

To achieve meaningful questions, we apply the following rules:

First, read the manual;
Check if your question has been asked previously;
Try to ask your question as clearly as possible;
Did you already try to solve the problem? Please mention this;
Is your problem solved by a visitor then let him/her know in this forum;
To give a response to a question or answer, do not use this form but click on the button 'reply to this question';
Your question will be posted here and emailed to our subscribers. Therefore, avoid filling in personal details.

new questions and answers
new manuals

You will receive an email to register for one or both of the options.

Get your user manual by e-mail

Enter your email address to receive the manual of Christopeit XL 2 in the language / languages: English, German, Dutch, French as an attachment in your email.

The manual is 1,46 mb in size.

You will receive the manual in your email within minutes. If you have not received an email, then probably have entered the wrong email address or your mailbox is too full. In addition, it may be that your ISP may have a maximum size for emails to receive.

The manual is sent by email. Check your email

If you have not received an email with the manual within fifteen minutes, it may be that you have a entered a wrong email address or that your ISP has set a maximum size to receive email that is smaller than the size of the manual.

The email address you have provided is not correct.

Please check the email address and correct it.

Your question is posted on this page

Would you like to receive an email when new answers and questions are posted? Please enter your email address.

Info

Christopeit XL 2 Manual

Product: